Metrohm tiamo 2.1 Manual Manuel d'utilisateur

tiamo 2.1Online Help8.101.8015EN

Table of contents￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭VIII￭￭￭￭￭￭￭￭tiamo 2.16.7 Subwindow Sensors ... 12566.7.1 Se

3.1 Workplace - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭86￭￭￭￭￭￭￭￭tiamo 2.1The original view of all subwindows is restored when the button is clickedin the max

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭986￭￭￭￭￭￭￭￭tiamo 2.1Identifi-cationDescription.ENPElectrode zero point calculated from the calibration.ETEEnd temper

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭987not definedIn this case, the device name must be assigned by the user at the start ofthe method.Devi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭988￭￭￭￭￭￭￭￭tiamo 2.1NoteIf an existing solution is selected as the solution to be added then theConcentration and Un

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭989StirrerStirrerSelection of the stirrer.Selection1 | 2 | 3 | 4 | offDefault value1offNo stirrer will

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭990￭￭￭￭￭￭￭￭tiamo 2.1Stop volumeVolume of auxiliary solution (e.g. buffer) that is to be added to the samplebefore th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭991The parameters for the measuring procedure can be defined on this tab.Measurement with drift control

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭992￭￭￭￭￭￭￭￭tiamo 2.1Switch off stirrer during measurementSwitch off stirrer during measurementon | off (Default valu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭993The calibration can be carried out with both manual and automatic solutionchanges with the aid of a

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭994￭￭￭￭￭￭￭￭tiamo 2.1￭ CAL MEAS ConcMeasurement of standards for the calibration of ion-selective electrodes(ISE elec

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭995method run, a request for specifying the next the buffer or standard is dis-played after each measur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭87Subwindow Method￭ Zoom￭ Modify parameters live￭ Interrupt commandsSubwindow Report￭ Select a repor

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭996￭￭￭￭￭￭￭￭tiamo 2.1The request for changing the buffer or standard must be deactivated inthe command CAL LOOP pH or

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭997NoteThe formula editor is opened with a right click in the input field.5.6.5.4 CAL LOOP pH5.6.5.4.1

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭998￭￭￭￭￭￭￭￭tiamo 2.1Identifi-cationDescription.SLOElectrode slope calculated from the calibration5.6.5.4.2 CAL LOOP

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭999NoteThe automatic buffer recognition is deactivated for the buffer type Spe-cial and the buffers mus

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1000￭￭￭￭￭￭￭￭tiamo 2.1Temp. (°C) Met4 Met7 Met9 pH 4.00 pH 7.00 pH 9.0010 3.99 7.06 9.1315 3.99 7.04 9.0820 3.99 7.0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1001Temp. (°C) NIST1 NIST4 NIST7 NIST9 NIST13 pH 1 pH 4 pH 7 pH 9 pH 1335 1.691 4.025 6.843 9.107 12.1

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1002￭￭￭￭￭￭￭￭tiamo 2.1Temp. (°C) DIN1 DIN3 DIN4 DIN7 DIN9 DIN12 pH 1 pH 3 pH 4 pH 7 pH 9 pH 1260 1.11 3.04 4.70 6.76

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1003Temp. (°C) Fis2 Fis4 Fis7 Fis10 pH 2 pH 4 pH 7 pH 1085 - 4.18 7.06 9.6190 - 4.21 7.08 9.6095 - 4.2

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1004￭￭￭￭￭￭￭￭tiamo 2.1Mettler-ToledoTemp. (°C) MT2 MT4 MT7 MT9 MT11 pH 2 pH 4 pH 7 pH 9 pH 110 2.03 4.01 7.12 9.52 1

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1005Temp. (°C) Mer2 Mer4 Mer7 Mer9 Mer12 pH 2 pH 4 pH 7 pH 9 pH 1220 2.00 4.00 7.00 9.00 12.0025 2.00

3.1 Workplace - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭88￭￭￭￭￭￭￭￭tiamo 2.1Automatic loadThe standard procedure is that the view saved when the program is termi-

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1006￭￭￭￭￭￭￭￭tiamo 2.1Temp. (°C) MerC4.01 MerC7.00 MerC9.00 MerC10.00 pH 4.01 pH 7.00 pH 9.00 pH 10.0045 4.05 6.97 8

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1007Temp. (°C) Bec4 Bec7 Bec10 pH 4 pH 7 pH 1070 4.12 6.99 -75 4.14 7.00 -80 4.16 7.00 -85 4.18 7.01 -

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1008￭￭￭￭￭￭￭￭tiamo 2.1Temp. (°C) Rad4.01 Rad7.00 Rad9.18 pH 4.01 pH 7 pH 9.1895 4.240 - -BakerTemp. (°C) Bak4 Bak7 B

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1009Temp. (°C) Ham4.01 Ham7.00 Ham9.21 Ham10.01 pH 4.01 pH 7.00 pH 9.21 pH10.015 4.01 7.09 9.45 10.191

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1010￭￭￭￭￭￭￭￭tiamo 2.1Temp. (°C) Pre4 Pre7 Pre9 pH 4.00 pH 7.00 pH 9.0030 4.00 6.99 8.9635 4.01 6.98 8.9340 4.02 6.9

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1011ParametersThe parameters for the command CAL MEAS pH are configured on thefollowing 2 tabs:￭ Genera

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1012￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription.MTE Temperature measurement with sensor; 1 = on, 0 =off).NMPNumber o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1013Titrando, 867Selection1 | 2Default value1855Selection1Default value1TitrinoSelection1 | 2 | diffDef

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1014￭￭￭￭￭￭￭￭tiamo 2.1offMeans that no stirrer will be used.Stirring rateSetting the stirring rate. The algebraic sig

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1015Min. waiting timeThe measured value is not accepted until the minimum waiting time haselapsed, even

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭89Move the selected subwindow upward (modifies sequence).Move the selected subwindow downward (modif

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1016￭￭￭￭￭￭￭￭tiamo 2.1Range-20.0 ... 150.0 °CDefault value25.0 °C5.6.5.6 CAL LOOP Conc5.6.5.6.1 CAL LOOP Conc - Ove

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭10175.6.5.6.2 CAL LOOP Conc - PropertiesDialog window: Method ▶ CAL LOOP Conc ▶ Properties.. ▶ CAL LOO

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1018￭￭￭￭￭￭￭￭tiamo 2.1DevicesThis command can be executed with the following devices:Titrando: 808, 809, 835, 836, 85

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1019Identifica-tionDescription.ITEInitial temperature (temperature before start conditionsare processed

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1020￭￭￭￭￭￭￭￭tiamo 2.1If the option not defined is selected as Device name, any device types ordevice groups which ar

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1021Selection1 | 2 | 3 | 4 | offDefault value1offMeans that no stirrer will be used.Stirring rateSettin

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1022￭￭￭￭￭￭￭￭tiamo 2.1Max. waiting timeIf the signal drift has not yet been reached, then the measured value will bea

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1023ParametersThe parameters for the command CAL Cond are configured on the follow-ing 3 tabs:￭ General

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1024￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription.LP.TEMTemperature for the last measuring point of the measur-ing poi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1025SensorSensorSelection of a conductivity sensor from the conductivity sensors available inthe sensor

3.2 Workplaces￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭90￭￭￭￭￭￭￭￭tiamo 2.13.1.7.5 Rename viewDialog window:Workplace / Database / Configura-tion ▶ View ▶ Rename view… ▶

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1026￭￭￭￭￭￭￭￭tiamo 2.1Switch off automaticallyon | off (Default value: off)If this option is enabled, the stirrer wil

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1027NoteA constant measured value is often only achieved after a certain time, asmixing and possibly th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1028￭￭￭￭￭￭￭￭tiamo 2.1856Range0.1 ... 999999.0 sDefault value2.0 sMeasurement without drift controlIf the option Meas

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1029SelectionInput | Request | TemplateDefault valueInputInputIf this option is selected, then the valu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1030￭￭￭￭￭￭￭￭tiamo 2.1Name standardList box with conductivity standards. The data of one of these standards isused to

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1031AppearanceThe command has the following appearance:ParametersThe parameters for the command CAL Con

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1032￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.CP{#}.MEAMeasured wavelength of the calibration point in nm. Ifno me

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭10335.6.5.9.3 CAL Spec - Measuring parametersTab: Method ▶ CAL Spec ▶ Properties... ▶ Measuring parame

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1034￭￭￭￭￭￭￭￭tiamo 2.1[Properties]Opens the dialog window Calibration wavelength # to edit the valuesselected in the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1035Titrando: 808, 809, 835, 836, 841, 842, 851, 852, 857, 888, 890, 901,902, 904, 905, 906, 907Titrino

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭91NameEntry of a name for the selected workplace or selection from the list of the10 names most rece

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1036￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription.TITERTiter value of the solution used for the command.VOLCurrently d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1037Titrando, 846, 856, 867Selection1 | 2 | 3 | 4Default value1778, 789, 814, 815, 855, 864, 874Selecti

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1038￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 846, 856, 867Selection1 | 2 | 3 | 4Default value2814, 815, 855, 864, 874Selection1 |

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1039Stirring rateSetting the stirring rate. The algebraic sign of the stirring rate changes thedirectio

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1040￭￭￭￭￭￭￭￭tiamo 2.1Dosing rateThe rate at which the volume is dosed. The maximum dosing rate dependson the cylinde

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1041Fill automatically at starton | off (Default value: on)If this option is enabled, the buret is fill

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1042￭￭￭￭￭￭￭￭tiamo 2.1CommandsDepending on the measured value, one of the following two DOS com-mands can be selected

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1043The time defined as Dosing time corresponds to the net dosing time t1+t2,i.e. the filling time of t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1044￭￭￭￭￭￭￭￭tiamo 2.1Flow rate of a single dosing deviceThe cylinder volume and the filling time of the exchange or

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1045Cylinder volume Filling time in s max. 100 mL/min 50 mL/min 10 mL/min1 mL 24/--- --- --- ---2 mL -

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭92￭￭￭￭￭￭￭￭tiamo 2.13.2.3.2 Displaying single workplacesMenu item: Workplace ▶ View ▶ UnsplitIn the default set

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1046￭￭￭￭￭￭￭￭tiamo 2.1AnyEither one of the two sizes.Limit exceedingSelects the exceeded limit for which a track is t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1047ParametersThe parameters for the command DOS pH are configured in the following5 tabs:￭ General/Har

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1048￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription.IMEInitial measured value (measured value before start con-ditions a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭10495.6.6.3.4.2 DOS pH - General/HardwareTab: Method ▶ DOS pH ▶ Properties... ▶ General/HardwareComman

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1050￭￭￭￭￭￭￭￭tiamo 2.1855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectioninternal D0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1051SolutionInput of a solution name or selection of a solution from the solutions definedin the soluti

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1052￭￭￭￭￭￭￭￭tiamo 2.1SensorSelection of a sensor of type pH electrode from the list of sensors availablein the senso

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1053Switch off automaticallyon | off (Default value: on)If this option is enabled, the stirrer will be

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1054￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0.01 ... 166.00 mL/minDefault valuemaximum mL/minTitrinoRange0.01 ... 150.00

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1055Titrando, 855Range0.1 ... 999999 sDefault value5.0 sTitrinoRange1 ... 999999 sDefault value5 s5.6.6

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭93NameName of the sample table.SavedDate and time when the sample table was saved.Saved byShort name

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1056￭￭￭￭￭￭￭￭tiamo 2.1offMeans that no stop will take place.Filling rateRate at which the dosing cylinder is to be fi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1057Titrando, 855Range-20.000 ... 20.000 Default value-20.000 TitrinoRange-20.00 ... 20.00 Default valu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1058￭￭￭￭￭￭￭￭tiamo 2.1Stop determinationThe running DOS command is quit, then the exit track (if present) isstarted a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1059Upper limitUpper limit of the temperature. When the temperature exceeds this value,the action Tempe

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1060￭￭￭￭￭￭￭￭tiamo 2.1Track call on limit exceedingIn this table, which cannot be edited directly, max. 20 entries ca

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1061[Delete]Deletes the calculated measured value selected in the table.Additional external measured va

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1062￭￭￭￭￭￭￭￭tiamo 2.1ParametersThe parameters for the command DOS U are configured in the following 5tabs:￭ General/

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1063Identifica-tionDescription.FIN Command status; 1 = Command has been ended atleast once, 0, invalid

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1064￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription.VOLDosed volume5.6.6.3.5.2 DOS U - General/HardwareTab: Method ▶ DO

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1065855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectioninternal D0 | e

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭94￭￭￭￭￭￭￭￭tiamo 2.1IncrementAutomatically increments selected lines.FillingAutomatically fills selected lines.T

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1066￭￭￭￭￭￭￭￭tiamo 2.1SolutionInput of a solution name or selection of a solution from the solutions definedin the so

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1067SensorSelection of a sensor of type pH electrode, metal electrode, pH elec-trode or ISE electrode f

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1068￭￭￭￭￭￭￭￭tiamo 2.1Switch off automaticallyon | off (Default value: on)If this option is enabled, the stirrer will

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1069Titrando, 855Range0.01 ... 166.00 mL/minDefault valuemaximum mL/minTitrinoRange0.01 ... 150.00 mL/m

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1070￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0.1 ... 999999 sDefault value5.0 sTitrinoRange1 ... 999999 sDefault value5 s5

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1071device, it will automatically be reduced during dosing to the largest possiblevalue.Titrando, 855Ra

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1072￭￭￭￭￭￭￭￭tiamo 2.1Lower hysteresisLower hysteresis of the measured value. If the measured value exceeds thelower

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1073Wait for [Continue]Reagent dosing in the current DOS command is interrupted and a mes-sage appears.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1074￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range-20.0 ... 150.0 °CDefault value150.0 °CTitrinoRange-170.0 ... 500.0 °CDefault

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1075Track call on limit exceedingIn this table, which cannot be edited directly, a maximum of 20 entrie

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭95Unmark linesRemoves the line marking for the selected lines.Set lines inexecutableSets the selecte

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1076￭￭￭￭￭￭￭￭tiamo 2.1[Delete]Deletes the calculated measured value selected in the table.Additional external measure

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1077AppearanceThe command has the following appearance:ParametersThe parameters for the command LQH are

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1078￭￭￭￭￭￭￭￭tiamo 2.1DeviceDevice nameSelection of a device from those available in the device table. The only devi-

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1079of the working life, the validity of the titer and the GLP test interval for theselected solution.S

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1080￭￭￭￭￭￭￭￭tiamo 2.1Exchange positionWith this function the cylinder is filled via the given port first. The valve

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1081DosingRange0.00000 ... 99999.9 mLDefault value10.0000 mLAspirateRange0.00000 ... 50.0 mLDefault val

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1082￭￭￭￭￭￭￭￭tiamo 2.1ParametersThe parameters for the command PREP are configured in the followingdialog window:￭ PR

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1083Device typeDisplay or selection of the device type. If a device is selected under Devicename, then

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1084￭￭￭￭￭￭￭￭tiamo 2.1Selection'Solution name' | not definedDefault valuenot definednot definedNo tests wil

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1085Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; invalid (variable

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1￭￭￭￭￭￭￭￭IX7.5.4 Properties - MSB # ... 13287

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭96￭￭￭￭￭￭￭￭tiamo 2.1NoteIf a method is changed and saved in the method editor or during reproc-essing, then the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1086￭￭￭￭￭￭￭￭tiamo 2.1Dosing deviceDosing deviceSelection of the dosing device (Dosinos only) to be emptied. All the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭10875.6.7 Automation commands5.6.7.1 Automation commands - OverviewMenu item: Method ▶ Paste ▶ New co

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1088￭￭￭￭￭￭￭￭tiamo 2.1￭ MOVE - PropertiesCommand variablesThe following command variables are generated in the method

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1089Device typeDisplay or selection of the device type. If a device is selected under Devicename, then

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1090￭￭￭￭￭￭￭￭tiamo 2.1Move = Rack positionRange1 ... 999 Default value1 Move = Special beaker (for 778, 789, 814, 815

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1091Stop determination and seriesThe determination as well as the series are stopped. An Exit track wil

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1092￭￭￭￭￭￭￭￭tiamo 2.1AppearanceThe command has the following appearance:ParametersThe parameters for the command SWI

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1093Selection'Device name' | not definedDefault valuenot definednot definedIn this case, the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1094￭￭￭￭￭￭￭￭tiamo 2.1Range1 ... 4 Default value1 Swing angleAngle by which the robotic arm is to be swung relative t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1095Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; invalid (variable

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭97NoteIf a value is entered or imported into this field, then in addition the timeof the data entry

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1096￭￭￭￭￭￭￭￭tiamo 2.1TargetTowerSelection of the tower of the Sample Processor for moving to the requiredlift positi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1097778, 789, 814, 815, 855, 864, 874Range5 ... 25 mm/sDefault value25 mm/s730Range3 ... 25 mm/sDefault

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1098￭￭￭￭￭￭￭￭tiamo 2.1Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; invalid (vari

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1099Selection1 | 2Default value1Pump(s)Selection of the pump that is to be actuated. The pump(s) can ei

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1100￭￭￭￭￭￭￭￭tiamo 2.1Coulometer: 756, 831Dosing Interface: 846pH/Ion - Meter: 867Sample Processor: 730, 778, 789, 81

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1101DeviceDevice nameSelection of a device from those available in the device table. The only devi-ces

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1102￭￭￭￭￭￭￭￭tiamo 2.1Stirrer typeDisplay of the stirrer type. Unknown is displayed either with devices unableto read

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1103Period of operationThe stirrer can be switched on for a particular period.Range0 ... 9999.9 Default

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1104￭￭￭￭￭￭￭￭tiamo 2.15.6.7.7.2 RACK - PropertiesDialog window: Method ▶ RACK ▶ Properties... ▶ RACK - 'Command

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭11055.6.7.8 HEATER5.6.7.8.1 HEATER - OverviewDialog window: Method ▶ HEATER ▶ Properties... ▶ HEATER

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭98￭￭￭￭￭￭￭￭tiamo 2.1Jump to the next line in the sample table. If the end of the table has beenreached, then a n

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1106￭￭￭￭￭￭￭￭tiamo 2.1DeviceDevice nameSelection of a device from those available in the device table. The only devi-

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1107Off causes heating at the maximum possible heating rate (see device man-ual).Range1 ... 999 minSele

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1108￭￭￭￭￭￭￭￭tiamo 2.1AppearanceThe command has the following appearance:ParametersThe parameters for the command FLO

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1109Device typeDisplay or selection of the device type. If a device is selected under Devicename, then

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1110￭￭￭￭￭￭￭￭tiamo 2.1Gas flowSelectionSwitch on | Switch offDefault valueSwitch onSwitch onSwitches on the gas flow.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1111Result parametersThe parameters for the individual results on the results table are configuredon th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1112￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription.OVF Limit value violation for result; 1 = limit exceeded, 0 =limit n

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1113Result nameName of the result.FormulaCalculation formula of the result.DeviceResult unit.Decimal pl

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1114￭￭￭￭￭￭￭￭tiamo 2.15.6.8.2.4 CALC - Formula assistantDialog window Method ▶ CALC ▶ [New] ▶ New resultat ▶ Formula

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1115Select result variableAll of the result variables of the formula template will be listed.'Vari

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭993.3.1.6 Importing sample dataDialog window: Workplace ▶ Sample table / Determination series ▶ [Sa

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1116￭￭￭￭￭￭￭￭tiamo 2.1DeviceUnit of the result for the output (text only). The unit can be used in furthercalculation

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1117Statisticson | off (Default value: on)Mean value, absolute and relative standard deviations are cal

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1118￭￭￭￭￭￭￭￭tiamo 2.1into the text field (see Chapter 2.5.2, page 79). The formula editor can alsobe called up insid

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1119Stop determinationThe determination is stopped and the next determination of the series isstarted.S

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1120￭￭￭￭￭￭￭￭tiamo 2.1Save result as titeron | off (Default value: off)If this option is enabled, then the result wil

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭11215.6.8.2.6.2 Save result templateDialog window: Method ▶ CALC ▶ Properties... ▶ [New] ▶ [Continue]

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1122￭￭￭￭￭￭￭￭tiamo 2.1AppearanceThe command has the following appearance:ParametersThe parameters for the command DAT

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1123DatabaseName of the database in which the determination data is stored.[New]Opens the dialog window

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1124￭￭￭￭￭￭￭￭tiamo 2.1Command variablesThe following command variables are generated in the method run by thecommand

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1125PDF fileon | off (Default value: off)The report is stored as PDF file in the directory selected if

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭100￭￭￭￭￭￭￭￭tiamo 2.1File typePrescribed format *.csv.Selection[*.csv]Default value[*.csv][Save]The sample data

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1126￭￭￭￭￭￭￭￭tiamo 2.1Identifi-cationDescription.FIN Command status; 1 = Command has been ended atleast once, 0, inva

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭11275.6.9.2 CTRL5.6.9.2.1 CTRL - OverviewDialog window: Method ▶ CTRL ▶ Properties... ▶ CTRL - '

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1128￭￭￭￭￭￭￭￭tiamo 2.1Identifi-cationDescription.FIN Command status; 1 = Command has ended at leastonce, 0, invalid (

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1129Set linesOutput signalInput of the binary pattern for the output signal or selecting a predefinedsi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1130￭￭￭￭￭￭￭￭tiamo 2.1NoteFor Titrinos with 3 output lines: only the first 3 characters are used.5.6.9.3 SCAN5.6.9.3

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1131Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; invalid (variable

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1132￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 856, 867, 814, 815, 855, 864, 874Selection1 | 2 | 3 | 4Default value1Scan linesInput

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭11335.6.9.4 SEND5.6.9.4.1 SEND - OverviewDialog window: Method ▶ SEND ▶ Properties... ▶ SEND - '

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1134￭￭￭￭￭￭￭￭tiamo 2.1NoteA maximum of 10 event messages can be entered.[New]Opens the dialog window Send event messa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1135Recipi-entSelec-tionEventmes-sageSignificanceSystem-HoldHold determination (all tracks). Thiscorres

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭101Sample table test finished with errorsThis display appears if an error has occurred during the sa

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1136￭￭￭￭￭￭￭￭tiamo 2.1Recipi-entSelec-tionEventmes-sageSignificanceCom-mandSET, KFT,KFCStartTitra-tionStart titration

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1137￭ RECEIVE - PropertiesCommand variablesThe following command variables are generated in the method

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1138￭￭￭￭￭￭￭￭tiamo 2.1[Properties]Opens the dialog window Wait for event/status to edit the event messageselected in

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1139Event/StatusType Significance Com-mandsStartEvent Command has been started. AllEndEvent Command has

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1140￭￭￭￭￭￭￭￭tiamo 2.1ParametersThe parameters for the command TRANSFER are configured in the fol-lowing dialog windo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1141Device typeDisplay or selection of the device type. If a device is selected under Devicename, then

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1142￭￭￭￭￭￭￭￭tiamo 2.1Selectionmin | sDefault values5.6.9.6.3 TRANSFER - Transfer commandDialog window: Method ▶ TRA

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1143NoteAll ASCII characters can be entered with its two-digit hex code after back-slash (e.g. \1B = Es

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1144￭￭￭￭￭￭￭￭tiamo 2.1[abc]OR function for single charac-tersreceive a or b or c[a-z0-9]one character in the specifie

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1145ParametersThe parameters for the command WEIGH are configured in the followingdialog window:￭ WEIGH

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭102￭￭￭￭￭￭￭￭tiamo 2.1[Save]Save the sample table under the desired name.3.3.1.10 Print sample table (PDF)Dialog

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1146￭￭￭￭￭￭￭￭tiamo 2.1Device typeDisplay or selection of the device type. If a device is selected under Devicename, t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭11475.6.10 Miscellaneous commands5.6.10.1 Miscellaneous commands - OverviewMenu item: Method ▶ Paste

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1148￭￭￭￭￭￭￭￭tiamo 2.1Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; invalid (vari

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1149NoteText is selected as type in the default settings for the sample identifica-tions ID1 … ID16. If

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1150￭￭￭￭￭￭￭￭tiamo 2.15.6.10.2.3 REQUEST - Sample data requestDialog window: Workplace ▶ [START] ▶ Sample data reque

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1151NoteSample data can be loaded directly from a balance or a barcodereader. The data import must be e

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1152￭￭￭￭￭￭￭￭tiamo 2.1Command variablesThe following command variables are generated in the method run by thecommand

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1153[Properties]Opens the dialog window Call to edit the call selected in the table (seeChapter 5.6.10.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1154￭￭￭￭￭￭￭￭tiamo 2.1A LOOP command just inserted has an arrow on the left-hand side withwhich a loop can be created

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1155

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭103Operating elementsNoteThis parameter group is visible only if the dialog window above the tabDete

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1156￭￭￭￭￭￭￭￭tiamo 2.1The LOOP command is at the end of the loop for Repeat loops. As soonas one stop criterion is fu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭11575.6.10.4.2 LOOP - PropertiesDialog window: Method ▶ LOOP ▶ Properties... ▶ LOOP - Loop #Command na

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1158￭￭￭￭￭￭￭￭tiamo 2.1The input field contains the expression for the condition(s) which can becreated or edited with

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭11595.6.10.5.2 WAIT - PropertiesDialog window: Method ▶ WAIT ▶ Properties... ▶ WAIT - 'Command na

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1160￭￭￭￭￭￭￭￭tiamo 2.1Record messageon | off (Default value: off)If this option is enabled, the message defined in th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭1161Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; invalid (variable

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1162￭￭￭￭￭￭￭￭tiamo 2.1PasteUse this context-sensitive menu item to paste the commands at the end of thetable that wer

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭11636 Configuration6.1 Configuration - General6.1.1 Configuration - DefinitionProgram part: C

6.1 Configuration - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1164￭￭￭￭￭￭￭￭tiamo 2.16.1.3 Configuration - Menu bar6.1.3.1 Configuration - Main menusProgram part:

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1165Load view...Load a saved configuration view (see Chapter 3.1.7.3, page 89).Save view...Save

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭104￭￭￭￭￭￭￭￭tiamo 2.1Sample dataNoteThe names defined here will be used only for the column headings in thesampl

6.1 Configuration - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1166￭￭￭￭￭￭￭￭tiamo 2.16.1.4 Configuration - ToolbarProgram part: ConfigurationChange layout...Modify

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1167PresentationThe subwindows can be enlarged or made smaller to suit by dragging theseparating

6.1 Configuration - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1168￭￭￭￭￭￭￭￭tiamo 2.1Backup/Restore configuration data￭ Backup configuration data automatically￭ Save

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1169Automatic loadThe standard procedure is that the view saved when the program is termi-nated

6.1 Configuration - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1170￭￭￭￭￭￭￭￭tiamo 2.1Move the selected subwindow upward (modifies sequence).Move the selected subwind

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭11716.1.7.5 Rename viewDialog window:Workplace / Database / Configura-tion ▶ View ▶ Rename view

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1172￭￭￭￭￭￭￭￭tiamo 2.1StructureThe dialog window User administration is divided into two parts, the sizeof whic

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1173DescriptionDescription of the user group.Input256 characters[Rename group]Renames selected u

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1174￭￭￭￭￭￭￭￭tiamo 2.1deactivated. If a subitem, e.g. the menu Tools, is deactivated in the con-figuration then

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1175Delete signatures Level 2If this check box is enabled then users in this user group can dele

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭105Input50 charactersDefault valueSample sizeUniton | off (Default value: on)Enable/disable the disp

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1176￭￭￭￭￭￭￭￭tiamo 2.1Executable methodsOnly methods with Signature Level 2If this check box is enabled, then o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1177Group nameName of new group.Input24 charactersWith [OK] a new group is generated under this

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1178￭￭￭￭￭￭￭￭tiamo 2.1NoteIt is only possible to delete a user group when the group no longer con-tains any use

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1179removedUsers with the status removed can no longer log in. If the status of auser is changed

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1180￭￭￭￭￭￭￭￭tiamo 2.1UserShort name of new user that must be used to log in at program start. Afterthe name ha

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1181Security settings can be exported and imported. This means that these set-tings can be excha

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1182￭￭￭￭￭￭￭￭tiamo 2.1as his/her user name. If this check box is disabled, then all subsequentparameters are de

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1183NoteWith Windows 2000, proceed as follows for password monitoring byWindows:1. Run/Execute &

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1184￭￭￭￭￭￭￭￭tiamo 2.1Selectionon | offDefault valueoffFDA default: offNoteIf the automatic logout is enabled (

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1185NoteThe immediate termination of all determinations on all activated work-places with the em

Table of contents￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭X￭￭￭￭￭￭￭￭tiamo 2.17.11.8 External position ... 137

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭106￭￭￭￭￭￭￭￭tiamo 2.1Copy automatically into next lineMethodon | off (Default value: on)If this option is enable

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1186￭￭￭￭￭￭￭￭tiamo 2.1Range1 ... 999 DaysDefault value365 DaysFDA default: 365 days6.2.2.3 Test login for pass

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1187ModificationsComment on modification of methodsIf this check box is enabled then each time t

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1188￭￭￭￭￭￭￭￭tiamo 2.1Selectionon | offDefault valueoffFDA default: onRange1 ... 60 minDefault value10 minFDA d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1189[New]Adds a new reason.[Edit]Edits the selected reason.[Delete]Deletes the selected reason.6

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1190￭￭￭￭￭￭￭￭tiamo 2.1Authenticationon | off (Default value: off)Check box for activating the authentication of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1191￭ LicensesList of installed licenses with number of clients. This tab is only shown onthe se

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1192￭￭￭￭￭￭￭￭tiamo 2.1NoteIf the backup directory is on a network drive the saving date should beadded manually

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭11936.2.3.3 ClientsTab: Configuration ▶ Tools ▶ Program administration ▶ ClientsTable with info

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1194￭￭￭￭￭￭￭￭tiamo 2.1NoteIn client/server systems this tab is only visible on the server and only formembe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1195Common variableson | off (Default value: on)Exports configuration data for common variables

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭1073.3.2.4 Properties - Process Dialog window:Workplace ▶ Tools ▶ Sample table ▶ New… ▶ Sam-ple tab

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1196￭￭￭￭￭￭￭￭tiamo 2.1Buffer dataon | off (Default value: on)Exports configuration data for custom buffers

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1197Deviceson | off (Default value: on)Imports configuration data for devices (see Chapter 6.5.1

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1198￭￭￭￭￭￭￭￭tiamo 2.1 Result templateson | off (Default value: on)Imports saved result templates (see Chap

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭11996.3.2 Backup/Restore6.3.2.1 Backup configuration data automatically Dialog window: Backup

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1200￭￭￭￭￭￭￭￭tiamo 2.16.3.2.2 Backup configuration data manually Dialog window: Backup ▶ Configuration ▶ F

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1201￭ tiamo multiMake sure that tiamo is closed on all clients connected to the serverand on the

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1202￭￭￭￭￭￭￭￭tiamo 2.1[Start]Starts the recovery of the configuration database. After the start, a progress

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1203NoteFor your own calibration buffers you should enter the pH values for theparticular temper

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1204￭￭￭￭￭￭￭￭tiamo 2.11 = Line active and* = Any line status.SelectionBit-pattern with 8 characters (0, 1,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1205Creating new template or editing templateWith <New> or <Edit> the dialog window

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭108￭￭￭￭￭￭￭￭tiamo 2.1Stop series ([Stop])If this option is selected, then the series is stopped before the start

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1206￭￭￭￭￭￭￭￭tiamo 2.1Start Dos1 *****p********Starts Dosimat 1 (Titrino via "acti-vate")Start Do

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1207Input1000 charactersMeasured observational pairsTable with the value pairs for Temperature a

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1208￭￭￭￭￭￭￭￭tiamo 2.1[New]Generates a new template. The window Edit E-mail template opens, inwhich a new t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1209Range1 ... 1 … 65536 Default value25 Authenticationon | off (Default value: off)Check box fo

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1210￭￭￭￭￭￭￭￭tiamo 2.16.3.4.2 Options - GeneralTab: Configuration ▶ Tools ▶ Options ▶ Options ▶ GeneralDia

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1211then any alterations that may have been made to the view will not be savedand at the next pr

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1212￭￭￭￭￭￭￭￭tiamo 2.16.4 Audit Trail6.4.1 Audit Trail - General6.4.1.1 Audit Trail - Definition Program window

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭12136.4.1.3 Audit Trail - Menu bar6.4.1.3.1 Audit Trail - Main menus Program window: Configura

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1214￭￭￭￭￭￭￭￭tiamo 2.1Special filter...Defines and uses special filter (see Chapter 6.4.2.3.4.1, page 1219).Remove

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1215SelectionAll entries | Quick filter | Temporary filter | FilternameDefault valueAll entriesA

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭109Always accept dataIf this option is selected, then the data sent from the balance is importedinto

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1216￭￭￭￭￭￭￭￭tiamo 2.16.4.1.7 Audit Trail - Functions Program window: Configuration ▶ Tools ▶ Audit Trail... ▶ Au

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1217DateDate, time and time zone of the action.UserShort name of the logged-in user.Full nameFul

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1218￭￭￭￭￭￭￭￭tiamo 2.1￭ Filter Audit Trail￭ Update Audit Trail￭ Export Audit Trail￭ Archive Audit Trail￭ Delete Au

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1219￭ Remove filter6.4.2.3.2 Audit Trail - Last filter Menu item: Audit Trail ▶ Filter ▶ Last f

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1220￭￭￭￭￭￭￭￭tiamo 2.1[Save filter]Opens the dialog window Save filter in which the filter criteria entered inthe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭12216.4.2.3.4.2 Special filter - Editing filter criterionDialog window: Audit Trail ▶ Filter ▶

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1222￭￭￭￭￭￭￭￭tiamo 2.1NoteIf for the column Date, the Operator Today is selected then filteringwill be carried out

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1223Filter nameName under which the special filter is to be saved.Input50 characters[Save]Saves

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1224￭￭￭￭￭￭￭￭tiamo 2.1SelectionSelectionAll records | Selected recordsDefault valueAll recordsAll recordsAll the e

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1225NoteArchiving Audit Trail entries is identical to exporting them, i.e. the AuditTrail entrie

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭110￭￭￭￭￭￭￭￭tiamo 2.1Import from fileon | off (Default value: off)If this option is enabled, then external data

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1226￭￭￭￭￭￭￭￭tiamo 2.1Input24 characters6.4.2.8 Print Audit Trail Dialog window: Audit Trail ▶ File ▶ Print (PDF)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1227Maximum numberMaximum number of entries allowed in the Audit Trail table. If this numberis e

6.5 Subwindow Devices￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1228￭￭￭￭￭￭￭￭tiamo 2.1Peripheral devices of USB devicesPeripheral devices connected to USB devices (e.g. dos

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1229NoteThe device status is permanently monitored and updated for USB devicesonly. For Metrohm

6.5 Subwindow Devices￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1230￭￭￭￭￭￭￭￭tiamo 2.1FunctionsThe menu [Edit] beneath the device table contains the following menuitems:New

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭12316.5.2.4 Devices - Column displayDialog window: Configuration ▶ Devices ▶ [Edit] ▶ Column di

6.5 Subwindow Devices￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1232￭￭￭￭￭￭￭￭tiamo 2.1Table contentsThe following information concerning the ignored devices is shown in the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1233￭ 756/831 Coulometer￭ 712 Conductometer￭ 856 Conductometer￭ 867 pH Module￭ 846 Dosing Interf

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1234￭￭￭￭￭￭￭￭tiamo 2.16.6.2 Solution table6.6.2.1 Solution tableSubwindow:Configuration ▶ Titra

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1235NoteLines that contain red entries will also show the line number with a redbackground.Table

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭111Entering a comment on the sample table.Comment on sample tableEntering a comment on the sample ta

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1236￭￭￭￭￭￭￭￭tiamo 2.1NoteSolutions in intelligent 806 Exchange Units (IEU) or 807 Dosing Units (

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭12376.6.2.5 Print list of solutionsDialog window: Configuration ▶ Titrants/Solutions ▶ [Edit] ▶

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1238￭￭￭￭￭￭￭￭tiamo 2.16.6.3.2 Properties - SolutionTab: Configuration ▶ Titrants/Solutions ▶ [Ed

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1239Range0 ... 999 DaysDefault value999 DaysExpiry dateExpiry date of the solution. The date can

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1240￭￭￭￭￭￭￭￭tiamo 2.16.6.3.3 Properties - TiterTab: Configuration ▶ Titrants/solutions ▶ Proper

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1241Rel. standard dev. (s rel)Relative standard deviation for the titer determination in %.Monit

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1242￭￭￭￭￭￭￭￭tiamo 2.1SelectionRecord message | Display message | Stop deter-minationDefault valu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1243NoteThis parameter is not saved on the data chip of intelligent exchange/dos-ing units, i.e.

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1244￭￭￭￭￭￭￭￭tiamo 2.16.6.3.5 Titer history Limit valuesDialog window: Configuration ▶ Titrants/

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭12456.6.3.6 Properties - Exchange unitTab: Configuration ▶ Titrants/solutions ▶ Properties ▶ Ex

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭112￭￭￭￭￭￭￭￭tiamo 2.1CopyCopies the selected sample table(s) (see Chapter 3.3.3.3, page 112).Delete…Deletes the

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1246￭￭￭￭￭￭￭￭tiamo 2.1IEUInput8 charactersDefault value'empty'EUInput10 charactersDefau

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1247Maximum Dosing/Filling rate for exchange unit as a function of thecylinder volume:Cylinder v

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1248￭￭￭￭￭￭￭￭tiamo 2.1LengthLength of the tubing connecting the cock to the cylinder.Range0.0 ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭12496.6.3.7 Properties - Dosing unitTab:Configuration ▶ Titrants/Solutions ▶ Properties... ▶ Do

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1250￭￭￭￭￭￭￭￭tiamo 2.1Input24 charactersDefault value'empty'Serial numberSerial number

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1251Dosing rate Dosing port 2Speed at which dosing is to be carried out at Dosing port 2. The ma

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1252￭￭￭￭￭￭￭￭tiamo 2.1Tubing parametersDefines the length and diameter of the tubing connected to

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1253Range0.0 ... 999.9 cmDefault value0.0 cmDiameterDiameter of tubing attached to Dosing port 2

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1254￭￭￭￭￭￭￭￭tiamo 2.1Range0.0 ... 9.9 mmDefault value2.0 mm Port assignment of dosing unit:Valve

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1255Comment GLP testComment on GLP test.Input1000 charactersMonitoring of GLP validityMonitoring

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭1133.3.3.6 Importing sample tableDialog window: Workplace ▶ Tools ▶ Sample table ▶ Man-ager… ▶ [Edi

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1256￭￭￭￭￭￭￭￭tiamo 2.1Acoustic signalon | off (Default value: off)If this option is enabled, an acoustic sig

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1257Standard sensorsThe sensor table contains the following sensors as standard; these cannotbe

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1258￭￭￭￭￭￭￭￭tiamo 2.1pH(0)/E(0)Electrode zero point of the sensor.Next calibrationDate on which the next ca

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭12596.7.2.2 Sensors - Column displayDialog window: Configuration ▶ Sensors ▶ Edit ▶ Column disp

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1260￭￭￭￭￭￭￭￭tiamo 2.1IonSelectionAg | BF4 | Br | Ca | Cd | Cl | CN | Cu | F | I | K | Na |NH4 | NO2 | NO3 |

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1261[OK]The sensor table is produced in the required format as a PDF file and can beopened direc

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1262￭￭￭￭￭￭￭￭tiamo 2.1Order numberOrder number of the sensor (read-only for intelligent sensors).Input24 cha

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1263Sensor monitoringon | off (Default value: off)If this option is switched on then the working

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1264￭￭￭￭￭￭￭￭tiamo 2.1SelectionRecord message | Display message | Stop deter-minationDefault valueDisplay me

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1265Specific calibration data for ISE electrodesSlopeSlope of the ISE electrode. This value can

3.4 Sample assignment table￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭114￭￭￭￭￭￭￭￭tiamo 2.1Method, the table can be sorted according to the selected column in eitherincreas

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1266￭￭￭￭￭￭￭￭tiamo 2.1Shared calibration dataCalibration temperatureTemperature during the calibration. The

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1267NoteThe days are monitored, e.g. the calibration becomes invalid when thedate changes and no

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1268￭￭￭￭￭￭￭￭tiamo 2.1SelectionRecord message | Display message | Stop deter-minationDefault valueDisplay me

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1269for ISE (-1)Range-2.147E+9 ... 2.147E+9 mVDefault value-61.0 mVfor ISE (+2)Range2.147E+9 ...

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1270￭￭￭￭￭￭￭￭tiamo 2.1for ISE (-2)Range-2.147E+9 ... 2.147E+9 mVDefault value-25.0 mVfor ISE (+3)Range-2.147

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1271message appears and you can choose whether you will nevertheless acceptthe value or whether

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1272￭￭￭￭￭￭￭￭tiamo 2.1pH electrodes, the Slope and the pH(0) are displayed, for ISE electrodes theSlope, E(0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1273￭ Black, when the values have been entered manually.If limits have been defined then the war

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1274￭￭￭￭￭￭￭￭tiamo 2.1Warning limits for slope (only for pH and ISE electrodes)on | off (Default value: off)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1275Upper limitUpper warning limit for the slope.for pH electrodeRange-2.147E+9 ... 2.147E+9 %De

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭115Open the dialog window Open method for the extended method selection.If a method is selected in t

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1276￭￭￭￭￭￭￭￭tiamo 2.1Lower limitLower intervention limit for the slope.for pH electrodeRange-2.147E+9 ... 2

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1277for ISE (+1)Range-2.147E+9 ... 2.147E+9 mVDefault value62.4 mVfor ISE (-1)Range-2.147E+9 ...

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1278￭￭￭￭￭￭￭￭tiamo 2.1Range-2.147E+9 ... 2.147E+9 Default value7.500 Intervention limits for pH(0) (only for

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1279Range-2.147E+9 ... 2.147E+9 mVDefault value-30 mVUpper limitUpper intervention limit for E(0

6.8 Common variables subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1280￭￭￭￭￭￭￭￭tiamo 2.16.8 Common variables subwindow6.8.1 Configuration - Common variables Subwin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1281UnitUnit of the common variables.Assignment dateDate of the last value assignment for the co

6.8 Common variables subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1282￭￭￭￭￭￭￭￭tiamo 2.1New…Adds new common variable manually (see Chapter 6.8.2.2, page 1282).Delete

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1283Removes the selected column from the table.Modifies the sequence of displayed columns by mov

6.8 Common variables subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1284￭￭￭￭￭￭￭￭tiamo 2.16.8.3.2 Properties - Common variableTab: Configuration ▶ Common variables ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1285Input256 charactersAssignment dateDate and time at which the last value was assigned; this i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1￭￭￭￭￭￭￭￭XI7.18.2 Barcode reader - Overview ... 14137.18.

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭116￭￭￭￭￭￭￭￭tiamo 2.1[New]Add new text template (see Chapter 3.5.2, page 116).[Properties]Edit selected text tem

6.8 Common variables subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1286￭￭￭￭￭￭￭￭tiamo 2.1Message by E-mailon | off (Default value: off)The message is additionally sen

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1287ValueThe values are shown in the following colors:￭ Blue, if the value has been assigned aut

6.8 Common variables subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1288￭￭￭￭￭￭￭￭tiamo 2.16.8.3.4 History - LimitsDialog window: Configuration ▶ Common variables ▶ [E

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭12896.9 Sample solutions (TC conductivity) subwindow6.9.1 Sample solutions (TC conductivity) -

6.9 Sample solutions (TC conductivity) subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1290￭￭￭￭￭￭￭￭tiamo 2.1c0 ... c4Coefficients of the Chebyshev polynomial for the c

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1291If the contents of a field is larger than the column width then the wholecontents will be sh

6.9 Sample solutions (TC conductivity) subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1292￭￭￭￭￭￭￭￭tiamo 2.1Removes the selected column from the table.Modifies the seq

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭12936.9.3.2 Properties - GeneralTab: Configuration ▶ Sample solutions (TC conductivity) ▶ [Edit

6.9 Sample solutions (TC conductivity) subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1294￭￭￭￭￭￭￭￭tiamo 2.1c0 ... c4Coefficients of the Chebyshev polynomial for the c

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1295SelectionDate selectionMessageThe message options can only be edited if monitoring is switch

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭1173.6.2 Run testMenu item: Workplace ▶ Tools ▶ Run testNoteIn contrast to the Sample table test, w

6.10 Rack data subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1296￭￭￭￭￭￭￭￭tiamo 2.16.10 Rack data subwindow6.10.1 Configuration - Rack data Subwindow: Configurati

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1297Table viewThe rack table cannot be edited directly. With a click on the column title thetabl

6.10 Rack data subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1298￭￭￭￭￭￭￭￭tiamo 2.1Rack nameName for the new rack. The selected name must not already exist.Input25 ch

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1299in by the Sample Processor in order to recognize the rack. If no rack is inposition then the

6.10 Rack data subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1300￭￭￭￭￭￭￭￭tiamo 2.1Rack offsetThe rack offset is a production-dependent tolerance value between theupp

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1301Range0 ... 235 mmRinse positionRinse position for Lift 2. This lift position is used for rin

6.10 Rack data subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1302￭￭￭￭￭￭￭￭tiamo 2.1Work position Tower 1Work position for the special beaker at Tower 1.Work position

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1￭￭￭￭￭￭￭￭1303Beaker radiusRadius of the selected special beaker on the rack. If the lift is moved to thew

6.10 Rack data subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1304￭￭￭￭￭￭￭￭tiamo 2.1￭ Special beakersDisplay of the special beaker for the rack in position.6.10.3.7 P

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭13057 Devices7.1 Titrando7.1.1 Titrando - OverviewThe parameters for the 808, 809, 835, 836, 841, 8

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭118￭￭￭￭￭￭￭￭tiamo 2.1Run test errorThis display appears if an error has occurred during the run test. Duringa de

7.1 Titrando￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1306￭￭￭￭￭￭￭￭tiamo 2.1Device typeDisplay of the device type.Program versionShows the program version of the device.On

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1307Measuring input 1/2 (iConnect)ADC typeShows the type of analog-digital converter.Serial numberShow

7.1 Titrando￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1308￭￭￭￭￭￭￭￭tiamo 2.1At program starton | off (Default value: on)If this option is switched on then at each program

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭13097.1.5 Properties - GLPTab: Configuration ▶ Device ▶ [Edit] ▶ Properties... ▶ 'Properties - &

7.1 Titrando￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1310￭￭￭￭￭￭￭￭tiamo 2.1Message by E-mailon | off (Default value: off)The message is additionally sent to the e-mail ad

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1311Old versionShows the old device program version.New versionShows the new device program version to

7.2 Titrino￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1312￭￭￭￭￭￭￭￭tiamo 2.1Titrino Program version702 SM Titrino 5.702.0021716 DMS Titrino 5.716.0022718 STAT Titrino 5.718

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1313[Update]Opens the dialog window Load new program version (see Chapter7.1.6, page 1310).This button

7.2 Titrino￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1314￭￭￭￭￭￭￭￭tiamo 2.1At program starton | off (Default value: on)If this option is switched on then at each program s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1315Time intervalon | off (Default value: off)If this option is switched on then the request to prepar

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭119The button is present in the status BUSY (determination is running), CONDREADY (condition require

7.2 Titrino￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1316￭￭￭￭￭￭￭￭tiamo 2.1NoteThese parameters are only editable for devices with status not ok (powersupply and/or RS con

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1317Only editable when the monitoring is activated.Default value 　　　 GLP test date + 999 daysMessageTh

7.3 756/831 Coulometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1318￭￭￭￭￭￭￭￭tiamo 2.17.3 756/831 Coulometer7.3.1 756/831 Coulometer - OverviewDialog window: Configurati

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1319Start-upShows the date on which the device was automatically added to the devicetable.Data storage

7.3 756/831 Coulometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1320￭￭￭￭￭￭￭￭tiamo 2.1NoteThese parameters are only editable for devices with status not ok (powersupply an

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1321Only editable when the monitoring is activated.Default value 　　　 GLP test date + 999 daysMessageTh

7.4 712 Conductometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1322￭￭￭￭￭￭￭￭tiamo 2.17.4 712 Conductometer7.4.1 712 Conductometer - OverviewDialog window: Configuration

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1323Start-upShows the date on which the device was automatically added to the devicetable.Data storage

7.4 712 Conductometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1324￭￭￭￭￭￭￭￭tiamo 2.1NoteThese parameters are only editable for devices with status not ok (powersupply and

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1325Only editable when the monitoring is activated.Default value 　　　 GLP test date + 999 daysMessageTh

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭120￭￭￭￭￭￭￭￭tiamo 2.1ERRORError.3.6.3.4 Single determination - Determination parameters Subwindow: Run ▶ Sequen

7.5 856 Conductivity Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1326￭￭￭￭￭￭￭￭tiamo 2.17.5 856 Conductivity Module7.5.1 856 Conductivity Module - DeviceDialog window

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1327Device serial numberShows the serial number of the device.Start-upShows the date on which the devi

7.5 856 Conductivity Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1328￭￭￭￭￭￭￭￭tiamo 2.1R (25 °C)Nominal resistance of connected NTC sensor.Only visible with temperatur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1329allTime interval after which the request to prepare the dosing device willappear.Range0.1 ... 999.

7.5 856 Conductivity Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1330￭￭￭￭￭￭￭￭tiamo 2.1Monitoring of GLP validityMonitoring of GLP validityon | off (Default value: off

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1331ActionThe actions can only be edited if monitoring is switched on.If during monitoring it is found

7.6 867 pH Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1332￭￭￭￭￭￭￭￭tiamo 2.17.6.2 Properties - GeneralTab: Configuration ▶ Devices ▶ [Edit] ▶ Properties... ▶ Propert

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭13337.6.3 Properties - Measuring inputsTab: Configuration ▶ Devices ▶ [Edit] ▶ Properties... ▶ Prope

7.6 867 pH Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1334￭￭￭￭￭￭￭￭tiamo 2.17.6.4 Properties - MSB #Tab: Configuration ▶ Devices ▶ [Edit] ▶ Properties... ▶ Properti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1335Stirrer 1Stirrer typeDisplay of the stirrer type.Stirrer serial numberDisplay of the serial number

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭121menu item Delete statistics, whereby the already calculated statistics datais deleted at the same

7.6 867 pH Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1336￭￭￭￭￭￭￭￭tiamo 2.12.5.1, page 79). After the date has been entered, the field GLP test inter-val will be ada

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭13377.7 846 Dosing Interface7.7.1 846 Dosing Interface - OverviewDialog window: Configuration ▶ Devi

7.7 846 Dosing Interface￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1338￭￭￭￭￭￭￭￭tiamo 2.1Start-upShows the date on which the device was automatically added to the devicetab

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1339allTime interval after which the request to prepare the dosing device willappear.Range0.1 ... 999.

7.7 846 Dosing Interface￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1340￭￭￭￭￭￭￭￭tiamo 2.1Monitoring of GLP validityMonitoring of GLP validityon | off (Default value: off)If

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1341ActionThe actions can only be edited if monitoring is switched on.If during monitoring it is found

7.8 730 Sample Changer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1342￭￭￭￭￭￭￭￭tiamo 2.1￭ GLPInformation on GLP tests and GLP monitoring.7.8.2 Properties - GeneralTab: Conf

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1343Input1000 charactersDefault valueempty7.8.3 Properties - TowerTab: Configuration ▶ Devices ▶ [Edi

7.8 730 Sample Changer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1344￭￭￭￭￭￭￭￭tiamo 2.17.8.4 Properties - RackTab: Configuration ▶ Device ▶ [Edit] ▶ Properties... ▶ Proper

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1345NoteConnecting the dosing devices is described in the manual for the 730Sample Changer or 774 Oven

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭122￭￭￭￭￭￭￭￭tiamo 2.1Sample positionPosition of the sample on the rack. This number is used to move to thesample

7.8 730 Sample Changer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1346￭￭￭￭￭￭￭￭tiamo 2.1Comment GLP testComment on GLP test.Input1000 charactersMonitoring of GLP validityMon

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1347Acoustic signalon | off (Default value: off)If this option is enabled, an acoustic signal will be

7.9 774 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1348￭￭￭￭￭￭￭￭tiamo 2.1￭ Dosing deviceProperties of the connector and the dosing devices connected to

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1349Start-upShows the date on which the device was automatically added to the devicetable.Data storage

7.9 774 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1350￭￭￭￭￭￭￭￭tiamo 2.1Rack codeShows the rack code of the rack attached. The rack code corresponds t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭13517.9.6 Properties - OvenTab: Configuration ▶ Device ▶ [Edit] ▶ Properties... ▶ Properties - '

7.9 774 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1352￭￭￭￭￭￭￭￭tiamo 2.17.9.7 Properties - GasTab: Configuration ▶ Devices ▶ [Edit] ▶ Properties... ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1353[Disconnect]Disconnects the connection to the RS-232 device.NoteThese parameters are only editable

7.9 774 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1354￭￭￭￭￭￭￭￭tiamo 2.1Only editable when the monitoring is activated.Default value 　　　 GLP test date

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭13557.10 778/789 Sample Processor7.10.1 778/789 Sample Processor - OverviewDialog window: Configurat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭123Sample size unitSample size unit (initial weight). There are no restrictions on the text to beent

7.10 778/789 Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1356￭￭￭￭￭￭￭￭tiamo 2.1[Update]Opens the dialog window Load new program version (see Chapter7.1.6, pa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1357tions(see Chapter 6.10.3.2, page 1299) and Special beakers(see Chapter6.10.3.4, page 1301) will be

7.10 778/789 Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1358￭￭￭￭￭￭￭￭tiamo 2.1[Configuration]Opens the dialog window Configuration (see Chapter 7.11.7, page

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1359Range3 ... 20 °/sDefault value20 °/s[Rack Data]Opens the dialog window Rack data (see Chapter 6.10

7.10 778/789 Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1360￭￭￭￭￭￭￭￭tiamo 2.1Connected devicesInformation about the following peripheral devices connected

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1361NoteThese parameters are only editable for devices with status not ok (powersupply and/or RS conne

7.10 778/789 Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1362￭￭￭￭￭￭￭￭tiamo 2.1Only editable when the monitoring is activated.Default value 　　　 GLP test date

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭13637.11 814/815 USB Sample Processor7.11.1 814/815 USB Sample Processor - OverviewDialog window: Co

7.11 814/815 USB Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1364￭￭￭￭￭￭￭￭tiamo 2.1This button is only displayed with devices that have their own firmware. I

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1365this minimum beaker radius is undercut then the run will be stopped and anerror message will appea

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭124￭￭￭￭￭￭￭￭tiamo 2.1Sample positionPosition of the sample on the rack. This number is used to move to thesample

7.11 814/815 USB Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1366￭￭￭￭￭￭￭￭tiamo 2.1[Configuration]Opens the dialog window Configuration (see Chapter 7.11.7,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1367Range3 ... 20 °/sDefault value20 °/s[Rack Data]Opens the dialog window Rack data (see Chapter 6.10

7.11 814/815 USB Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1368￭￭￭￭￭￭￭￭tiamo 2.1Connected devicesInformation about the following peripheral devices connec

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1369GLP test intervalTime interval to next GLP test. If a value is entered here then the date in thefi

7.11 814/815 USB Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1370￭￭￭￭￭￭￭￭tiamo 2.1Display messageA message is displayed and you can choose whether you want

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1371Range-270.0 ... 270.0 °Default value0.0 °Swing directionThe swing direction of the robotic arm dep

7.12 855 Robotic Titrosampler￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1372￭￭￭￭￭￭￭￭tiamo 2.17.12 855 Robotic Titrosampler7.12.1 855 Robotic Titrosampler - OverviewDialo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1373This button is only displayed with devices that have their own firmware. Itis only active if the d

7.12 855 Robotic Titrosampler￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1374￭￭￭￭￭￭￭￭tiamo 2.1With the 856 Conductivity Module displayed only.SelectionPt 1000 | NTCDefault

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1375Lift rateLift speed for manual operation.Range3 ... 25 mm/sDefault value25 mm/sAxial distanceDista

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭125Sample size unitSample size unit (initial weight). There are no restrictions on the text to beent

7.12 855 Robotic Titrosampler￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1376￭￭￭￭￭￭￭￭tiamo 2.1Table for external positionsThe properties for the 4 possible external positio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1377[Rack Data]Opens the dialog window Rack data (see Chapter 6.10.3.1, page 1298) orRack data (774) (

7.12 855 Robotic Titrosampler￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1378￭￭￭￭￭￭￭￭tiamo 2.1Connected devicesInformation about the following peripheral devices connected

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1379GLP test intervalTime interval to next GLP test. If a value is entered here then the date in thefi

7.13 864 Balance Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1380￭￭￭￭￭￭￭￭tiamo 2.1Display messageA message is displayed and you can choose whether you want

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1381Program versionShows the program version of the device.Only visible with devices that have their o

7.13 864 Balance Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1382￭￭￭￭￭￭￭￭tiamo 2.1Min. beaker radiusDefinition of the minimum radius which the beakers used

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1383Rinse positionRinse position valid for all 4 external positions.Range0 ... 235 mmDefault value0 mm

7.13 864 Balance Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1384￭￭￭￭￭￭￭￭tiamo 2.1Number of positionsShows the number of positions on the rack. If no rack i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1385Time intervalon | off (Default value: off)If this option is switched on then the request to prepar

Table of contents￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭XII￭￭￭￭￭￭￭￭tiamo 2.19.4 Databases ... 14729

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭126￭￭￭￭￭￭￭￭tiamo 2.1￭ Check device (modules) and rackCheck whether the instruments (and/or instrument types), d

7.13 864 Balance Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1386￭￭￭￭￭￭￭￭tiamo 2.1Input1000 charactersMonitoring of GLP validityMonitoring of GLP validityon

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1387ActionThe actions can only be edited if monitoring is switched on.If during monitoring it is found

7.14 874 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1388￭￭￭￭￭￭￭￭tiamo 2.17.14.2 Properties - GeneralTab: Configuration ▶ Devices ▶ [Edit] ▶ Propertie

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭13897.14.3 Properties - TowerTab: Configuration ▶ Devices ▶ [Edit] ▶ Properties... ▶ Properties - &ap

7.14 874 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1390￭￭￭￭￭￭￭￭tiamo 2.1[Rack Data]Opens the dialog window Rack data (see Chapter 6.10.3.1, page 1298

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1391Connected devicesInformation about the following peripheral devices connected to the MSBconnector

7.14 874 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1392￭￭￭￭￭￭￭￭tiamo 2.1With the 774 Oven Sample Processor display of the initial temperature seton t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1393Monitoring can only be switched on when a date has been entered in thefield GLP test date.GLP test

7.15 Avantes Spectrometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1394￭￭￭￭￭￭￭￭tiamo 2.1Record messageThe message that the validity period has expired will be automatical

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1395Input50 charactersDefault valueDevice type number_#Device typeDisplay of the device type.Program v

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭127￭ Check sample dataCheck whether the sample data entered corresponds to the definedmethod variabl

7.15 Avantes Spectrometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1396￭￭￭￭￭￭￭￭tiamo 2.1Selectioncontinuous | pulsedDefault valuecontinuousPulses per integration timeFreq

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭13977.15.5 Properties - CalibrationTab: Configuration ▶ Devices ▶ [Edit] ▶ Properties... ▶ Properties

7.15 Avantes Spectrometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1398￭￭￭￭￭￭￭￭tiamo 2.1DateDisplay of date and time the dark spectrum has been recorded.UserDisplay of th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1399UserDisplay of the user logged in during recording of the reference spectrum.MethodDisplay of the

7.15 Avantes Spectrometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1400￭￭￭￭￭￭￭￭tiamo 2.1Monitoring of GLP validityMonitoring of GLP validityon | off (Default value: off)I

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1401ActionThe actions can only be edited if monitoring is switched on.If during monitoring it is found

7.16 RS-232 device￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1402￭￭￭￭￭￭￭￭tiamo 2.1Input50 charactersDefault valueDevice type number_#Device typeDisplay of the device type.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1403SelectionCOM1 | COM2 | … | COMnDefault valueCOMnCOMnFirst free COM port.Baud rateTransmission rate

7.16 RS-232 device￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1404￭￭￭￭￭￭￭￭tiamo 2.1Selection\0D | \0D\0A | \0D\0A\0A | \0D\0D\0ADefault value\0D\0A(\0D = CR, \0A = LF)Termi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1405Input1000 charactersMonitoring of GLP validityMonitoring of GLP validityon | off (Default value: o

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭128￭￭￭￭￭￭￭￭tiamo 2.17 - Conditioning (only for methods with conditioning)Conditioning is started with the loade

7.16 RS-232 device￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1406￭￭￭￭￭￭￭￭tiamo 2.1ActionThe actions can only be edited if monitoring is switched on.If during monitoring it

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭14077.17 Balances7.17.1 Balance - OverviewDialog window: Configuration ▶ Devices ▶ [Edit] ▶ Properti

7.17 Balances￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1408￭￭￭￭￭￭￭￭tiamo 2.1Start-upShows the date on which the device was automatically added to the devicetable.Data sto

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1409SelectionNone | Odd | EvenDefault valueNoneStop bitNumber of stop bits.Selection1 | 2Default value

7.17 Balances￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1410￭￭￭￭￭￭￭￭tiamo 2.1GLP test intervalTime interval to next GLP test. If a value is entered here then the date in t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1411Display messageA message is displayed and you can choose whether you want to con-tinue the run or

7.18 Barcode reader￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1412￭￭￭￭￭￭￭￭tiamo 2.17.18 Barcode reader7.18.1 Barcode reader - GeneralA barcode reader is used to enter sa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭14137.18.2 Barcode reader - OverviewDialog window: Configuration ▶ Devices ▶ [Edit] ▶ Properties...

7.18 Barcode reader￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1414￭￭￭￭￭￭￭￭tiamo 2.1Data storage under legal controlIndicates whether the balance has its own calibratable d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1￭￭￭￭￭￭￭￭1415Input1000 charactersMonitoring of GLP validityMonitoring of GLP validityon | off (Default value: o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭1293.6.3.9.2 Properties - Display Dialog window: Workplace ▶ Run ▶ Single determination ▶ Propert

7.18 Barcode reader￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1416￭￭￭￭￭￭￭￭tiamo 2.1ActionThe actions can only be edited if monitoring is switched on.If during monitoring i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭14178 Manual Control8.1 Manual Control - GeneralProgram part: Manual ControlDefinitionIn tiam

8.3 Manual Control - Device selection￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1418￭￭￭￭￭￭￭￭tiamo 2.18.3 Manual Control - Device selectionProgram part: Manual ControlIn t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1419Titrino: 702, 716, 718, 719, 720, 721, 736, 751, 758, 785, 784, 785, 794,795, 798, 799Titra

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1420￭￭￭￭￭￭￭￭tiamo 2.1TiterDisplay of the titer of the solution put on. This field only appears for

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭14218.4.1.5 Dosing - EmptyProgram part: Manual ControlHere the emptying of dosing units can be

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1422￭￭￭￭￭￭￭￭tiamo 2.1730, 774, 778, 789Range0.01 ... 160.00 mL/minTitrinoRange0.01 ... 150.00 mL/m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1423NoteParameters modified after the start of the dosing are not valid until thenext dosing pr

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1424￭￭￭￭￭￭￭￭tiamo 2.1NoteFor viscous liquids the filling rate should be reduced.SelectionmaximumDe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1425Titrino: 751, 758, 785, 784, 785, 794, 795, 798, 799Titrando: 808, 809, 835, 836, 841, 842,

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭130￭￭￭￭￭￭￭￭tiamo 2.12 columnsIf this option is selected, then the sample identifications ID1…ID16 areshown in d

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1426￭￭￭￭￭￭￭￭tiamo 2.1[Start]Start continuous operation for the selected stirrer. In the status dis

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1427Output signalCurrent statusDisplays the current status of the 14 output lines.Templates/Inp

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1428￭￭￭￭￭￭￭￭tiamo 2.1NoteWe recommend masking the irrelevant output lines with an asterisk * soas

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1429Rack codeShows the number of positions on the rack attached. If no rack is attached,-------

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1430￭￭￭￭￭￭￭￭tiamo 2.1Current positionShows the current rack position.Target positionSelect or ente

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1431[Start]Start moving to target position. Start moving to target position. After thestart, th

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1432￭￭￭￭￭￭￭￭tiamo 2.1Current positionShows the current rack position.Special beakerSelect the spec

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1433Shift position forIf this option is selected, the current lift position is assigned to the

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1434￭￭￭￭￭￭￭￭tiamo 2.1External positionSelect the external position to which the current robotic ar

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1435SelectionOn/Off | DurationDefault valueOn/OffDurationEnter the duration during which the pu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭131Request assignment IDon | off (Default value: off)If this option is enabled, the Assignment ID wi

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1436￭￭￭￭￭￭￭￭tiamo 2.1Gas flowInletSelect the inlet of the carrier gas.SelectionPump | ValveDefault

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1437Inert gas valveSwitch the inert gas valve on the Oven Sample Processor on/off.[Start]Switch

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1438￭￭￭￭￭￭￭￭tiamo 2.1Measured quantityThe selectable measured quantities depend on the device whos

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1439TitrinoRange-127 ... 127 µA (Increment: 1)Default value5 µAU(pol)The polarization voltage i

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1440￭￭￭￭￭￭￭￭tiamo 2.1Sample solutionSelect name from the table Sample solution (TC conductivity).S

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1￭￭￭￭￭￭￭￭1441[Measuring]Start measuring of the intensity. The parameters defined will be used.8.4.5.4 M

9.1 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1442￭￭￭￭￭￭￭￭tiamo 2.19 How to proceed?9.1 Audit Trail9.1.1 Opening Audit Trail How to proceed?NoteThe Audit Tr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1443After this function has been selected, the field in which the cursor islocated will have a

9.1 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1444￭￭￭￭￭￭￭￭tiamo 2.1The dialog window Audit Trail opens. 3If desired, filter Audit Trail table. 4If desired, sel

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1445 4Enter or select directory and file name for saving the archive file in thefield Save fil

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭132￭￭￭￭￭￭￭￭tiamo 2.1SelectionAlways accept data | Accept data only foractive windowDefault valueAlways accept d

9.2 Backup￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1446￭￭￭￭￭￭￭￭tiamo 2.1 3Archive desired Audit Trail entries. 4With the menu item File ▶ Delete the dialog window Delete

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1447Backing up database manually 1Select program part Database. 2Click on the symbol or menu

9.2 Backup￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1448￭￭￭￭￭￭￭￭tiamo 2.1 4On the tab General enter a comment on the database in the fieldComment. 5On the tab Backup enab

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1449NoteExisting databases cannot be overwritten, i.e. they must first bedeleted so that the d

9.2 Backup￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1450￭￭￭￭￭￭￭￭tiamo 2.1NoteIf the backup directory is on a network drive. the backup date shouldbe added manually to the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1451The dialog window Restore configuration data opens. 3Select the directory in the Backup di

9.2 Backup￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1452￭￭￭￭￭￭￭￭tiamo 2.1 2Click on the menu item File ▶ Backup ▶ Manually.The dialog window Backup configuration data man

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1453Exporting methods 1Select program part Method. 2Click on the symbol or menu item File ▶

9.2 Backup￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1454￭￭￭￭￭￭￭￭tiamo 2.1 3Click on the menu item File ▶ Archive...The dialog window Archive Audit Trail opens. 4Enter or

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭14559.3 Determinations9.3.1 Starting single determinationHow to proceed?Single determination

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭133Confirmation necessary to accept data during the determination.on | off (Default value: off)If th

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1456￭￭￭￭￭￭￭￭tiamo 2.1NoteIn order to calculate statistical calculations for results, the Statis-tics option mu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1457 5If a method was loaded in which the option Statistics in the STARTcommand is enabled, di

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1458￭￭￭￭￭￭￭￭tiamo 2.1NoteIf the method contains a DATABASE command, then it is manda-tory that this command be

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1459The dialog window Open database opens. 3Select desired database or enter name in the field

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1460￭￭￭￭￭￭￭￭tiamo 2.1 4Click on [Save filter]. 5Click on [Apply filter].The table will be filtered.Using speci

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1461Signature 1NoteDeterminations can only be signed at level 1 if the user belongs to a userg

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1462￭￭￭￭￭￭￭￭tiamo 2.1The window Signature Level 2 opens; if a signature is possible forthe selected determinat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1463 2Click on the symbol or the menu item File ▶ Open...The dialog window Open database op

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1464￭￭￭￭￭￭￭￭tiamo 2.1 5Click on the menu item Determinations ▶ Import...The window Import determinations open

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1465NoteIf the option Comment on modification of determinations inthe Security settings is ena

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭134￭￭￭￭￭￭￭￭tiamo 2.1￭ Sample dataEntry of sample data for the next determinations.￭ PropertiesDefinition of the

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1466￭￭￭￭￭￭￭￭tiamo 2.19.3.10 Reprocessing determinations How to proceed?NoteDeterminations that have a signatu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1467The selected determinations are recalculated. The results of this recal-culation are enter

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1468￭￭￭￭￭￭￭￭tiamo 2.1The selected determinations are recalculated. The results of this recal-culation are ente

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1469If the determination is switched off then an asterisk (*) appears behindall result values

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1470￭￭￭￭￭￭￭￭tiamo 2.1 4Modify curve evaluation manually. 5Then close the window with [OK]. 6Click on [Recalcul

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1471 6Click on the menu item File ▶ Print ▶ Report...The dialog window Report output opens. 7

9.4 Databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1472￭￭￭￭￭￭￭￭tiamo 2.1NoteA maximum of 4 databases can be opened, but only 2 can be dis-played at the same time. Dat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1473NoteEach determination database has to be backed up separately. Afterwards,it is recommend

9.4 Databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1474￭￭￭￭￭￭￭￭tiamo 2.1Closing all databases 1Select program part Database. 2Click on menu item File ▶ Close all….All

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1475 9On tab Monitoring, define monitoring of size and number of datasets.9.4.5 Backing up da

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭135Interrupt seriesWith this button, the ongoing determination of a sample series will still becarri

9.4 Databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1476￭￭￭￭￭￭￭￭tiamo 2.1 3Select desired database. 4Click on [Properties].The dialog window Properties - Database - &a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1477 6Enter the name under Save as under which the database is to berestored. 7Click on [Start

9.5 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1478￭￭￭￭￭￭￭￭tiamo 2.19.5 Configuration data9.5.1 Configuration data in generalThe configuration data in

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭14799.5.3 Importing configuration dataHow to proceed?1Select program part Configuration. 2Cli

9.5 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1480￭￭￭￭￭￭￭￭tiamo 2.1 4Select or enter the name for the Backup file. If an existing backup fileis selected

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1481 2Start the file ConfigRestore.exe in the program directory …\tiamo\bin.The dialog window

9.6 Methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1482￭￭￭￭￭￭￭￭tiamo 2.19.6 Methods9.6.1 Open methodHow to proceed?1Select program part Method. 2Click on the symbol

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1483Close all methods 1Select program part Method. 2Click on menu item File ▶ Close all….All o

9.6 Methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1484￭￭￭￭￭￭￭￭tiamo 2.1 2In the list box Method group select the desired method group. 3Select the desired method from

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭14859.6.6 Exporting method How to proceed?1Select program part Method. 2Click on the symbol

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 Introductiontiamo 2.1￭￭￭￭￭￭￭￭11 Introduction1.1 Welcome to tiamoIntroductiontiamo = titration and moretiamo is a control and

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭136￭￭￭￭￭￭￭￭tiamo 2.1ERRORError.3.6.4.4 Determination series - Determination parameters Tab: Workplace ▶ Run ▶

9.6 Methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1486￭￭￭￭￭￭￭￭tiamo 2.1The dialog window Select files to import opens. 5Select desired import files named as 'Meth

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1487The selected method will be signed on level 1.NoteMethods can be signed more than once at

9.6 Methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1488￭￭￭￭￭￭￭￭tiamo 2.1The dialog window Method manager opens. 3In the list box Method group select the desired method

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭14899.6.11 Backup methodsHow to proceed?GeneralMethods are stored in the configuration databa

9.6 Methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1490￭￭￭￭￭￭￭￭tiamo 2.1 3Activate the Automatic backup check box. 4Enter an interval for backup monitoring in the field

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭14919.7 Method groups9.7.1 Creating method groupHow to proceed?1Select program part Method.

9.8 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1492￭￭￭￭￭￭￭￭tiamo 2.1 4Click on [Delete].The selected method group is deleted. 5Confirm deleting with [OK].9.8

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1493 9Repeat step 6 for each desired determination. 10Click on [Close].The dialog window Edit

9.8 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1494￭￭￭￭￭￭￭￭tiamo 2.1 9Click on the menu item Edit ▶ Edit line in the dialog window Sampletable.The dialog wind

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭14959.8.4 Edit working sample tableHow to proceed?1Select program part Workplace. 2In subwind

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭137The second field after Autostart shows the total number of determinationsper series that are stil

9.9 Reports￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1496￭￭￭￭￭￭￭￭tiamo 2.1 14In the field Name enter a name. 15Click on [Save].The working sample table will be saved unde

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1497 9Select desired module symbol on the Module bar and place it on thereport template by cre

9.9 Reports￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1498￭￭￭￭￭￭￭￭tiamo 2.1 7Close the dialog window with [OK]. 8In the program window Report template, click on the menu i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭14999.9.3 Printing determination report How to proceed?1Select program part Database. 2Click

9.9 Reports￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1500￭￭￭￭￭￭￭￭tiamo 2.1NoteIf several reports are produced simultaneously as a PDF file then anindex will be automatica

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1￭￭￭￭￭￭￭￭1501 8Under Orientation, select the option Portrait format or Landscapeformat. 9Click on [OK].

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1502￭￭￭￭￭￭￭￭tiamo 2.1IndexNummern/Symbole21 CFR 11 ... 14, 1180, 1181, 1186, 1187712 ConductometerOverview ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1￭￭￭￭￭￭￭￭1503Command variables ... 784Conditioning ... 794Control parameters ... 791

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1504￭￭￭￭￭￭￭￭tiamo 2.1MEAS Ref ... 956MEAS Spec ... 958MEAS T ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1￭￭￭￭￭￭￭￭1505x axis ... 308y axis ... 309, 311Curve overlayCommen

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭138￭￭￭￭￭￭￭￭tiamo 2.13.6.4.5 Determination series - Sample data Tab: Workplace ▶ Run ▶ Determination seriesTh

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1506￭￭￭￭￭￭￭￭tiamo 2.1Determination run ... 141Display ... 102, 155Edit ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1￭￭￭￭￭￭￭￭1507Parameters for preparing ... 1249Prepare ...

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1508￭￭￭￭￭￭￭￭tiamo 2.1Extraction time 655, 676, 697, 717, 739, 760, 778, 793FFDA ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1￭￭￭￭￭￭￭￭1509Configuration ... 333Determination ... 327Messages ...

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1510￭￭￭￭￭￭￭￭tiamo 2.1MEAS Ipol ... 884Additional measured values ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1￭￭￭￭￭￭￭￭1511Method selection by assignmentID ... 130Method symbol .. 13, 371, 37

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1512￭￭￭￭￭￭￭￭tiamo 2.1Report template ... 213News in tiamo 2.1 ... 9Normal track ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1￭￭￭￭￭￭￭￭1513Reason for modificationDetermination ... 316Recalculating ... 29

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1514￭￭￭￭￭￭￭￭tiamo 2.1SSample addition time 657, 678, 699, 720, 742, 762, 779, 794Sample assignment ... 113, 114Samp

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1￭￭￭￭￭￭￭￭1515Command variables ... 642Conditioning ... 657Control parameters ... 651

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭139Reset sample tableResets lines that have been run, i.e. they can be edited again.Duplicate Duplic

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1516￭￭￭￭￭￭￭￭tiamo 2.1Overview ... 799STAT pH ... 803STAT U ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1￭￭￭￭￭￭￭￭1517Input lines ... 1203Output lines ... 1204Text editor ...

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1518￭￭￭￭￭￭￭￭tiamo 2.1ViewChange layout .. 88, 186, 1169Default views ... 1176Delete ... 90, 188,

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭140￭￭￭￭￭￭￭￭tiamo 2.1Unmark linesRemoves the line marking for the selected lines.Set lines inexecutableSets the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭141RemarksFreely definable remarks concerning the determination, that are savedtogether with the det

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭142￭￭￭￭￭￭￭￭tiamo 2.1￭ Authorization for carrying out the method?Check whether the registered user is authorized

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭143￭ Conditioning condition fulfilledIf the conditioning requirement has been fulfilled, then the st

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭144￭￭￭￭￭￭￭￭tiamo 2.1￭ Interrupt and continue seriesA series that is running can be interrupted at any time with

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭145￭ Conditioning condition fulfilledIf the conditioning requirement has been fulfilled, then the st

1.2 Operation￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2￭￭￭￭￭￭￭￭tiamo 2.1￭ Database-based program with Client/Server functionality￭ A wide range of import and export func

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭146￭￭￭￭￭￭￭￭tiamo 2.1Loading sample tableNameName of the sample table that is to be loaded. If a sample table fr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭147for the quick selection of methods in the Method field. This button is activeonly if more than on

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭148￭￭￭￭￭￭￭￭tiamo 2.1NoteIf a value is entered or imported into this field, then in addition the timeof the data

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭149Jump to the previous line in the working sample table.Option of entering the desired line number

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭150￭￭￭￭￭￭￭￭tiamo 2.1Range1 ... 999 Default value1 3.6.4.9.5 Importing sample dataDialog window: Workplace ▶ Sa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭151File typePrescribed format *.csv.Selection[*.csv]Default value[*.csv][Save]The sample data will b

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭152￭￭￭￭￭￭￭￭tiamo 2.1Sample table test finished with errorsThis display appears if an error has occurred during

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭153[Save]Save the sample table under the desired name.3.6.4.9.9 Run testMenu item: Workplace ▶ Tool

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭154￭￭￭￭￭￭￭￭tiamo 2.1Run test running…This display appears during the test run. A progress bar also appears; the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭155￭ ProcessOptions for processing the working sample table on the tab Determi-nation series.￭ Data

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 Introductiontiamo 2.1￭￭￭￭￭￭￭￭31.3 Connecting devicesIntroductiontiamo brings together the world of Titrino devices and the ne

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭156￭￭￭￭￭￭￭￭tiamo 2.1Sample numberon | off (Default value: on)Enable/disable the display of the field Sample num

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭157Input50 charactersDefault valueID1…3ID4 … ID16on | off (Default value: off)Enable/disable the dis

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭158￭￭￭￭￭￭￭￭tiamo 2.1into the same line. This means that it is possible, for example, to fill a linefirst with s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭159Sample size uniton | off (Default value: on)If this option is enabled, then the content of this f

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭160￭￭￭￭￭￭￭￭tiamo 2.1Actions for marked sample table linesSelectionPause series ([Pause]) and show message | Sto

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭161BalanceSelection of the balance from which data is to be imported.SelectionDevice nameSelectionAl

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭162￭￭￭￭￭￭￭￭tiamo 2.1Accept data only for active windowIf this option is selected, then the data sent from the b

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭163*.csv (Unicode)Format for the import of CSV files with Unicode character sets.3.6.4.10.6 Propert

3.7 Subwindow Method￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭164￭￭￭￭￭￭￭￭tiamo 2.13.7 Subwindow Method3.7.1 Method window - GeneralSubwindow: Workplace ▶ MethodSubwindo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭165SelectionFit in windowDefault valueFit in windowAdjust to both height and width of the window.3.7

1.4 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4￭￭￭￭￭￭￭￭tiamo 2.11.4 Method editorIntroductionThe new graphic method editor gets more out of your titration s

3.8 Subwindow Live display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭166￭￭￭￭￭￭￭￭tiamo 2.13.7.4 Method window - Cancel commandSubwindow: Workplace ▶ MethodIf a workplace i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭167On these tabs the live display elements (curve, measured value, message)defined in the Properties

3.8 Subwindow Live display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭168￭￭￭￭￭￭￭￭tiamo 2.13.8.3 Live display - Application noteSubwindow: Workplace ▶ Live displayOn the ta

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭169Measured value 1…3Select the measured values for the measured value display. The measuredquantiti

3.8 Subwindow Live display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭170￭￭￭￭￭￭￭￭tiamo 2.1MEAS TC CondSelectionoff | Measured value | time | dMW/dt | Calcula-ted 1...3 | Ex

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭171KFC / BRCSelectiontime | Measured value | amount | drift | Charge| dV/dt | Ugen | Igen | Calculat

3.8 Subwindow Live display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭172￭￭￭￭￭￭￭￭tiamo 2.1METSelectionMeasured value | Volume | time | Temperature| dMW | Calculated 1…3 | E

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭173DOSSelectionVolume | Measured value | Temperature | time| dV/dt | Calculated 1…3 | External 1…3De

3.8 Subwindow Live display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭174￭￭￭￭￭￭￭￭tiamo 2.1MEASSelectionoff | Measured value | time | Temperature |dMW/dt | Calculated 1…3 |

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭175Display gridon | off (Default value: off)If this option is enabled, a grid will be displayedBackg

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 Introductiontiamo 2.1￭￭￭￭￭￭￭￭5in this network and can be accessed and processed by all Client PCs. Allclients also access the

3.9 Subwindow Report￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭176￭￭￭￭￭￭￭￭tiamo 2.13.9.4 Report overviewTab: Workplace ▶ Report ▶ Report overviewThe reports for the deter

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭1774 Database4.1 Database - General4.1.1 Database - DefinitionProgram part: DatabaseDefinitionThe

4.1 Database - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭178￭￭￭￭￭￭￭￭tiamo 2.1ElementsThe desktop of the program part Database comprises the following ele-ments:￭ D

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭179Report…PDF file output of the report (see Chapter 4.5.2.12, page 320).Logout...Logout user (see Ch

4.1 Database - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭180￭￭￭￭￭￭￭￭tiamo 2.14.1.3.5 Database - Menu DeterminationsProgram part: DatabaseComment...Enter comment o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭181Make current Make the old version selected in the history view the current version again (see"

4.1 Database - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭182￭￭￭￭￭￭￭￭tiamo 2.14.1.3.7 Help MenuProgram part: Workplace / Database / Method / Configurationtiamo Hel

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭183Filter/Quick filter Use quick filter with the content of the selected table cell (see Chapter 4.5.

4.1 Database - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭184￭￭￭￭￭￭￭￭tiamo 2.14.1.5 Database - SubwindowsProgram part: DatabaseSelectionThe following subwindows ca

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭185Determinations￭ Overview of functionsTemplates￭ Edit report templates￭ Edit control chart template

1.7 Conformity￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6￭￭￭￭￭￭￭￭tiamo 2.1￭ Various export formats , e.g. XML, CSV, SLK (see Chapter 4.4.4.2.1, page245).￭ Automatic data

4.1 Database - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭186￭￭￭￭￭￭￭￭tiamo 2.1As an alternative a standard view can be defined for each user group that isloaded aut

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭187Move the selected subwindow downward (modifies sequence).4.1.7.3 Load viewDialog window:Workplace

4.2 Database display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭188￭￭￭￭￭￭￭￭tiamo 2.14.1.7.5 Rename viewDialog window:Workplace / Database / Configura-tion ▶ View ▶ Rename

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭189EditableShows whether or not the database can be edited by the user currentlylogged in.CommentShow

4.2 Database display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭190￭￭￭￭￭￭￭￭tiamo 2.1Two databases are opened. Normally only one databaseis displayed in the main window but

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭1914.3 Manage databases4.3.1 Manage databasesDialog window: Database ▶ File ▶ Database manager… ▶ D

4.3 Manage databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭192￭￭￭￭￭￭￭￭tiamo 2.1[Properties]Opens the window Database manager for editing the database selectedin the ta

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭193NoteThe database name must be unambiguous in the whole Client/Server sys-tem.4.3.4 Deleting datab

4.3 Manage databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭194￭￭￭￭￭￭￭￭tiamo 2.1SizeShows the size of the database in KB.CreatedShows the date and time of the creation

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭1954.3.5.4 Database properties - BackupDialog window: Database ▶ File ▶ Database manager... ▶ Databa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 Introductiontiamo 2.1￭￭￭￭￭￭￭￭7￭ Digital signature on two levels (see Chapter 2.3, page 17).￭ One signature each for methods an

4.3 Manage databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭196￭￭￭￭￭￭￭￭tiamo 2.1NoteMake sure that you have read and write access rights on the selecteddirectory.4.3.5.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭197Backup targetBackup directorySelection of a folder predefined in Program administration for thebac

4.3 Manage databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭198￭￭￭￭￭￭￭￭tiamo 2.1Backup nameSelection of a backup file.SelectionSelect backup filesBackup dateShows the t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭1994.4 Templates4.4.1 Report templates4.4.1.1 Manage report templates4.4.1.1.1 Report template ma

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭200￭￭￭￭￭￭￭￭tiamo 2.14.4.1.1.2 Rename report templatesDialog window: Database ▶ Tools ▶ Report templates ▶ Manager…

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭2014.4.1.1.6 Import report templatesDialog window: Database ▶ Tools ▶ Report templates ▶ Manager… ▶

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭202￭￭￭￭￭￭￭￭tiamo 2.1SavedDate and time when the report template was saved.Saved byShort name of the user who saved

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭2034.4.1.4.1.2 Report template - DesktopProgram window: Database ▶ Report templateElementsThe deskto

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭204￭￭￭￭￭￭￭￭tiamo 2.1Print (PDF)... Show the report template with the data of the selected determination as a PDF-fi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭2054.4.1.4.1.3.6 Report template - Menu ToolsProgram window: Database ▶ Report templateOptions...Set

1.9 Online help￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8￭￭￭￭￭￭￭￭tiamo 2.11.9 Online helpIntroductionCalling up the Helptiamo has an extensive and detailed online help

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭206￭￭￭￭￭￭￭￭tiamo 2.14.4.1.4.1.5 Report template - Module-specific toolbar Program window: Database ▶ Report templa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭207Line If this option is switched on then lines can be inserted in the report template (seeChapter 4

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭208￭￭￭￭￭￭￭￭tiamo 2.1Apply to all pagesThe page settings are applied for all report pages.Page formatPage formatSele

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭209Range0.0 ... 499.0 mmDefault value20.0 mmRightRight-hand page margin.Range0.0 ... 499.0 mmDefault

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭210￭￭￭￭￭￭￭￭tiamo 2.1Defining sections for tabular reportThe header, footer and report sections can be enlarged and

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭211Jumps to last page.4.4.1.4.2.5 Report template - Insert modules Program window: Database ▶ Report

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭212￭￭￭￭￭￭￭￭tiamo 2.1Select a single moduleSingle modules are selected with a click of the left mouse button. This a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭2134.4.1.4.2.8 Report template - Page preview Preview window: Report template ▶ File ▶ Page preview

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭214￭￭￭￭￭￭￭￭tiamo 2.1Jumps to last determination. 4.4.1.4.2.9 Report template - CommentDialog window: Report templa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭215Snap at gridon | off (Default value: off)Enable/Disable snapping at grid on the report template.De

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 Introductiontiamo 2.1￭￭￭￭￭￭￭￭9WarningThis symbol draws attention to a possible hazard dueto heat or hot instrument parts.Warni

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭216￭￭￭￭￭￭￭￭tiamo 2.1Input50 charactersNoteThe name of the report template must be unambigous in the whole Client/Se

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭217Selection of the available Windows fonts.Font size in pt.Color selection.Bold.Italic.Underlined.Le

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭218￭￭￭￭￭￭￭￭tiamo 2.1InsertIn order to insert a data field into a report template the corresponding sym-bol must be

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭219Left-justified.Centered.Right-justified.Switches line break on/off for multi-line data fields.Fill

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭220￭￭￭￭￭￭￭￭tiamo 2.1InsertIn order to insert a date field into a report template the corresponding sym-bol must be

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭221Left-justified.Centered.Right-justified.Fills the field with dots.PrefixText placed in front of th

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭222￭￭￭￭￭￭￭￭tiamo 2.1Range0.0000 ... (max. page height) mmWidthWidth of time field.Range0.0000 ... (max. page width)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭223SuffixText to be placed after the contents of the time field.Input50 charactersPreviewShows the fo

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭224￭￭￭￭￭￭￭￭tiamo 2.1Color selection.Bold.Italic.Underlined.Left-justified.Centered.Right-justified.Fills the field

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭225InsertIn order to insert a number of pages field into a report template, the corre-sponding symbol

1.10 What is new in tiamo 2.1?￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭10￭￭￭￭￭￭￭￭tiamo 2.1￭ 778, 789: Exception if the lift is to be lowered at an invalid rack position.

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭226￭￭￭￭￭￭￭￭tiamo 2.1Left-justified.Centered.Right-justified.Fills the field with dots.PrefixText placed in front of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭227WidthShows the predefined width of the fixed report.HeightHeight of fixed report.Range0.0000 ... (

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭228￭￭￭￭￭￭￭￭tiamo 2.1NoteThe following fields, which do not permit page break controls, cannot beinserted into a gro

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭229PropertiesX pos.x-position within the permitted section.Range0.0000 ... (max. page width) mmY pos.

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭230￭￭￭￭￭￭￭￭tiamo 2.1InsertIn order to insert a line in a report template the corresponding symbol mustbe selected o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭2314.4.1.4.3.11 Report template - Rectangle Program window: Database ▶ Report templateAny rectangle

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭232￭￭￭￭￭￭￭￭tiamo 2.1Selection of the fill color.4.4.1.4.3.12 Report template - Curve field Program window: Databas

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭233SelectionDET | MET | SET | MEAS | MEAS T/Flow | MEASTC Cond | MEAS Ref | MEAS Opt | MEAS Spec |CAL

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭234￭￭￭￭￭￭￭￭tiamo 2.1InsertIn order to insert calibration curve field into a report template the corre-sponding symb

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭235Template tableThe table with the defined templates cannot be edited, although it can besorted acco

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭112 General program functions2.1 Program parts2.1.1 Program partsGeneral program

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭236￭￭￭￭￭￭￭￭tiamo 2.1￭ Graphical parametersParameters for the graphical display of the control chart.￭ LimitsDefinit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭237ColorSelection of the color for the measuring point symbol.SelectionColor selection | blueDefault

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭238￭￭￭￭￭￭￭￭tiamo 2.14.4.2.2.4 Control chart template - StatisticsDialog window: Database ▶ Tools ▶ Templates ▶ Con

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭239Template tableThe table with the defined templates cannot be edited, although it can besorted acco

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭240￭￭￭￭￭￭￭￭tiamo 2.1SelectionDET pH | DET U | DET Upol | DET Upol | METpH | MET U | MET Ipol | MET Upol | SET pH |

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭241ScalingStart valueInitial value for scaling the x axis.Range-1.0 E12 ... 1.0 E12 Default value0.0

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭242￭￭￭￭￭￭￭￭tiamo 2.1ScalingStart valueInitial value for scaling the y-axis.Range-1.0 E12 ... 1.0 E12 Default value0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭243Manual EPsSelects the color for manually set endpoints.SelectionColor selection | pinkDefault valu

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭244￭￭￭￭￭￭￭￭tiamo 2.14.4.4 Export templates4.4.4.1 Managing export templatesDialog window: Database ▶ Tools ▶ Temp

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭2454.4.4.2 Editing export templates4.4.4.2.1 Export template - Properties Dialog window: Database

2.1 Program parts￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭12￭￭￭￭￭￭￭￭tiamo 2.1Manual program part￭ Manual control of devicesNoteAccess to the individual program parts can

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭246￭￭￭￭￭￭￭￭tiamo 2.1*.csv (measuring point list)Data exchange format for the measuring point list with unformatted

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭247Sample identificationIf this option is selected then the name of the export file will be formedfro

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭248￭￭￭￭￭￭￭￭tiamo 2.1Remove selected field.Modifies the sequence of the exported fields by moving the selected field

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭249Field separatorSelection of the field separator.Selection; | , | TabDefault value;4.4.4.3 XML exp

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭250￭￭￭￭￭￭￭￭tiamo 2.1<userNameFull val="" />User name (full name)<clientName val="" /&g

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭251<determinationEndState val=""/>Determination run (way in which the determination w

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭252￭￭￭￭￭￭￭￭tiamo 2.1<status val="original"/>Determination status:originalDetermination data unalter

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭253<vt val=""/>Variable type:TX = TextNR = NumberDT = Date/TimeNA = Unknown<vn val

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭254￭￭￭￭￭￭￭￭tiamo 2.1– <comment>...</comment>Comment on the signature.</data> </signOff> <

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭255<savingTime val=""/>Date and time when the modified method version wassaved.<sa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭13shown in color. The upper left corner of the symbol contains a black fielddisplayi

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭256￭￭￭￭￭￭￭￭tiamo 2.1<vs val=""/>Variable status:OK = The value is ok and has not been monitored.OKL

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭257</SmplData> – <Identification>Sample identifications.– <ID__01>Sample identifica

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭258￭￭￭￭￭￭￭￭tiamo 2.1<pr val=""/>Name of the CALC command the result has been gener-ated with.<un

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭259<vs val=""/>Variable status (see above).</data> <rel> <n val="

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭260￭￭￭￭￭￭￭￭tiamo 2.1– <sme>Mean value of the result.– <data> <vr val="" />Mean value wi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭2614.4.4.3.6 XML export - Command dataXML export– <CommandData dynamic="">Command da

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭262￭￭￭￭￭￭￭￭tiamo 2.1– <swingHeadOneType> ... </swingHeadOneType>Type of Swing Head on tower 1.– <swi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭263– <conc> ... </conc>Concentration.– <concUnit> ... </concUnit>Concentratio

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭264￭￭￭￭￭￭￭￭tiamo 2.1<adcSerial val="" />Serial number of measuring input.<tempSensorType val=&qu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭265<sensorC val="" />Blank value of the ISE sensor.<resultUnit val="" /&

2.2 Login/password protection￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭14￭￭￭￭￭￭￭￭tiamo 2.1ElementsThe desktop of the program part Configuration comprises the followingele

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭266￭￭￭￭￭￭￭￭tiamo 2.1<variance val="" />Variance.– <StdAddTable>Standard addition solutions.–

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭267</tableBody> </MeasPoints> – <EndPoints dynamic="">Endpoints– <data

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭268￭￭￭￭￭￭￭￭tiamo 2.1<volume> ... </volume>Volume in mL.<otherVal> ... </otherVal>Temperatur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭269<am val="" />Assignment method.<at val="" />Assignment date.</d

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭270￭￭￭￭￭￭￭￭tiamo 2.1– <dateRecDarkRefSpec> ... </dateRecDarkRefSpec>Recording time of dark and referenc

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭271– <Solution>Data on solution.– <solTitle> ... </solTitle>Solution title.– <so

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭272￭￭￭￭￭￭￭￭tiamo 2.1– <usedSensors dynamic="">Sensor data– <Sensor>Data on sensor.<subtype

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭273<sensorCalMethod val="" />Calibration method.<sensorCalMeasInput val="&quo

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭274￭￭￭￭￭￭￭￭tiamo 2.1</TcSampleSolution> </TcSampleSolutions> 4.4.4.3.11 XML export - Method parameters

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭275– <sme> ... </sme>Mean value of the result.– <un> ... </un>Result unit.– &

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭15￭ A login with user name and password is required each time theprogram is started.

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭276￭￭￭￭￭￭￭￭tiamo 2.14.5 Determination overview4.5.1 Determination overview - General4.5.1.1 Determi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭277Table viewWith a click on the column title the table can be sorted according to theselected column

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭278￭￭￭￭￭￭￭￭tiamo 2.1Removes the selected column from the table.Move selected column upwards.Move selec

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭2794.5.1.5 Determination overview - Navigation barSubwindow: Database ▶ Determination overviewThe na

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭280￭￭￭￭￭￭￭￭tiamo 2.1[Page Up]Pages backward within the current set.[Page Down]Pages forward within the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭281￭ Several determinations not in sequenceIn order to select several determinations not in sequence

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭282￭￭￭￭￭￭￭￭tiamo 2.14.5.2 Determination overview - Functions4.5.2.1 Update determination overviewMen

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭283[More...]Open the dialog window Search – Field selection. All fields are listed intree-form. A fie

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭284￭￭￭￭￭￭￭￭tiamo 2.1outside limitsIt is being searched for values which exceed the limit values define

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭285SelectionTotal | Downward | UpwardDefault valueTotalTotalIt is being searched down to the end of t

Metrohm AGCH-9101 HerisauSwitzerlandPhone +41 71 353 85 85Fax +41 71 353 89 [email protected] 2.1Online Help8.101.8015EN 09.2009

2.2 Login/password protection￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭16￭￭￭￭￭￭￭￭tiamo 2.1[Change password]Opens the window Change password, in which the new password has

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭286￭￭￭￭￭￭￭￭tiamo 2.14.5.2.4.3 Determinations - Quick filter Menu item: Database ▶ Determinations ▶ Fi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭287Table viewThe overview table shows all the defined filter criteria and cannot be directlyedited. T

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭288￭￭￭￭￭￭￭￭tiamo 2.14.5.2.4.7 Determinations - Save filterDialog window: Database ▶ Determinations ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭289Selection'Field name'Filtering is carried out only for the selected field. The10 most re

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭290￭￭￭￭￭￭￭￭tiamo 2.1out of limitsValues that are out of the defined limits for the selected fields wil

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭2914.5.2.5 Signing determinations4.5.2.5.1 Rules for electronic signaturesProgram parts: Method / D

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭292￭￭￭￭￭￭￭￭tiamo 2.1Methods or determinations can be signed at Level 1 in the Signature Level1 window.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭293[Sign]Sign method or determination. The window remains open.NoteMethods or determinations can only

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭294￭￭￭￭￭￭￭￭tiamo 2.1Input24 charactersPasswordPassword entry.Input24 charactersReasonSelection from th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭295ReasonReason for signature.Signature commentComment on the signature.4.5.2.5.5 Delete Signature L

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭17NoteThe password always has to be changed before the Validity of the pass-word exp

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭296￭￭￭￭￭￭￭￭tiamo 2.14.5.2.6 Determinations - Reprocessing4.5.2.6.1 Reprocessing - GeneralDialog wind

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭297FunctionsIf determinations have been edited in the subwindow Modifications thenthe following funct

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭298￭￭￭￭￭￭￭￭tiamo 2.14.5.2.6.3 Reprocessing rulesDialog window: ReprocessingThe following rules apply

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭299￭ Titration and measuring commandsFor DET, MET, SET, KFT, KFC, MEAS, CAL MEAS only the evaluations

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭300￭￭￭￭￭￭￭￭tiamo 2.14.5.2.6.4 Modifications4.5.2.6.4.1 Modifications - OverviewSubwindow: Database ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭301[Modify]Open the dialog window Modify variable to modify the value of an existingvariable.NoteIf a

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭302￭￭￭￭￭￭￭￭tiamo 2.1(see Chapter 5.2.5, page 385). The modified method then appears on thetab Methods

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭303[Result on/off]Switch the selected single result for the statistical calculations off or on. Ifthe

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭304￭￭￭￭￭￭￭￭tiamo 2.1Command nameSelection of the measuring command (command name.index - com-mand type

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭305Set EP with parallel tangentsBy moving the mouse a point on the curve is selected to which thetang

2.3 Electronic signatures￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭18￭￭￭￭￭￭￭￭tiamo 2.1￭ Different usersThe same user may only sign on either Level 1 or Level 2.￭ Reason a

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭306￭￭￭￭￭￭￭￭tiamo 2.1Define properties for the graph displayThe dialog window Properties - Curves # is

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭307Measured valueMeasured value (pH) for endpoint.ERCERC value for the endpoint.TimeTime for the endp

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭308￭￭￭￭￭￭￭￭tiamo 2.14.5.2.6.4.6.4.2 Properties curve evaluation - x axisTab: Database ▶ Determination

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭309Only editable when the option Autoscaling is disabled.Range-1.0E12 ... 1.0E12 Default value1.0E12

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭310￭￭￭￭￭￭￭￭tiamo 2.1End valueEnd value for scaling the y-axis.Only editable when the option Autoscalin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭311Range0.01 ... 1000 Default value0.01 Smoothing factor y-axisFactor for smoothing on the y axis.Ran

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭312￭￭￭￭￭￭￭￭tiamo 2.1CurveCurve colorSelection of the color for the curve line.Selection13 colors | red

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭3134.5.2.6.4.6.4.5 Properties curve evaluation - OptionsTab: Database ▶ Determinations ▶ Reprocessin

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭314￭￭￭￭￭￭￭￭tiamo 2.1Show endpointsShow endpointson | off (Default value: on)If this option is enabled

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭3154.5.2.6.5.1 Result view - Results overviewTab: Database ▶ Determinations ▶ Reprocess... ▶ Reproce

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭19ModifyModifyNot sigendSign (1)Signed 1Sign (2)Sigend 2Delete signatures 2DeleteCre

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭316￭￭￭￭￭￭￭￭tiamo 2.14.5.2.6.5.2 Result view - Raw dataTab: Database ▶ Determinations ▶ Reprocess... ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭3174.5.2.7 Sending determinations toDialog window: Database ▶ Determinations ▶ Send to...The menu it

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭318￭￭￭￭￭￭￭￭tiamo 2.1All filtered data recordsAll those determinations from the whole determination tab

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭319NoteIf the check box Comment on modification of determinations in theSecurity settings is activate

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭320￭￭￭￭￭￭￭￭tiamo 2.14.5.2.12 Determinations - Print reportDialog window: Database ▶ File ▶ Print ▶ Re

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭321PDF fileon | off (Default value: off)If this check box is activated the reports are put out as PDF

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭322￭￭￭￭￭￭￭￭tiamo 2.14.5.2.14 Determinations - Displaying historyMenu item: Database ▶ Determinations

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭323values. Listed below are the individual measured values and the results forSlope, E(0), c(blank) a

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭324￭￭￭￭￭￭￭￭tiamo 2.1If the cursor is moved to a point then the number, date and value appear asa toolt

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭325right of the curve the legend is shown with the line number in the determi-nation table belonging

2.3 Electronic signatures￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭20￭￭￭￭￭￭￭￭tiamo 2.1Signature possibleThe selected method or determination can be signed.Signature 1 not

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭326￭￭￭￭￭￭￭￭tiamo 2.1PortraitProduces control chart in portrait format.LandscapeProduces control chart i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭3274.6.2 Information - Determination Tab: Database ▶ Information ▶ DeterminationDisplay of genera

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭328￭￭￭￭￭￭￭￭tiamo 2.1StopThe determination was stopped manually with [Stop], by a stop criterionor with

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭329Determination status:Selectionoriginal | modifiedoriginalDetermination data unaltered.modifiedDete

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭330￭￭￭￭￭￭￭￭tiamo 2.1Signed by (full name):Full name of user who signed the determination.Signature reas

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭331Method version:Version of the method the determination was created with.Method saving date:Date an

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭332￭￭￭￭￭￭￭￭tiamo 2.1Sample size:Value for the sample size.Sample size unit:Unit of sample size.Input da

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭333Modification reason sample data:Reason for the sample data modification.Modification comment sampl

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭334￭￭￭￭￭￭￭￭tiamo 2.1Measuring input:Number of the measuring input (+ designation iConnect for intellige

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭335Date titer det.:Date of the titer determination.Titer method:Method with which the titer was deter

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭21Methods or determinations can be signed at Level 2 in the Signature Level2 window.

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭336￭￭￭￭￭￭￭￭tiamo 2.1User dark/reference spectrum:User logged in during recording the dark spectrum and

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭337Measuring input:Number of the measuring input to which the sensor is connected (+ desig-nation iCo

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭338￭￭￭￭￭￭￭￭tiamo 2.1Assignment method:Method with which the value was assigned.Sample solution (TC cond

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭3394.6.6 Information - Messages Tab: Database ▶ Information ▶ MessagesShows messages generated durin

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭340￭￭￭￭￭￭￭￭tiamo 2.14.7 Subwindow Results4.7.1 Results - GeneralSubwindow: Database ▶ ResultsIn the subwi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭341NoteOnly the last results having been calculated will be shown. For example,if there are several c

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭342￭￭￭￭￭￭￭￭tiamo 2.14.7.3 Results - Raw dataTab: Database ▶ Results ▶ ResultsOn the tab Raw data the evalu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭343Table 3 Command DET IpolColumn 2: Variable Column 3 Column 4 Column 5 Column 6EP#EP#.VOL, mL, 4 EP

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭344￭￭￭￭￭￭￭￭tiamo 2.1Column 2: Variable Column 3 Column 4 Column 5 Column 6MAMA.VOL, mL, 4 MA.MEA, mV, 1 MA.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭345Table 10 Command SET UColumn 2: Variable Column 3 Column 4 Column 5 Column 6EP#EP#.VOL, mL, 4 EP#.

2.3 Electronic signatures￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭22￭￭￭￭￭￭￭￭tiamo 2.1[Sign]Sign method or determination. The window remains open.NoteMethods or determina

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭346￭￭￭￭￭￭￭￭tiamo 2.1Table 14 Command KFT UpolColumn 2: Variable Column 3 Column 4 Column 5 Column 6EPEP.VOL

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭347Column 2: Variable Column 3 Column 4 Column 5 Column 6RE#RE#.DRT, mL/min,4RE#.DRS,mL/min,4RE#.DRC,

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭348￭￭￭￭￭￭￭￭tiamo 2.1Column 2: Variable Column 3 Column 4 Column 5 Column 6ETEETE, °C, 1 FP#FP#.MEA, µA,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭349Column 2: Variable Column 3 Column 4 Column 5 Column 6MAMA.MEA, mS/cm,2MA.TIM, s, 1 MA.TEM, °C, 1

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭350￭￭￭￭￭￭￭￭tiamo 2.1Table 33 Command CAL CondColumn 2: Variable Column 3 Column 4 Column 5 Column 6CLCCLC,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭351For every single result a maximum of the following information is displayed:Result "Result na

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭352￭￭￭￭￭￭￭￭tiamo 2.1Assignment:Assigns the result to one of the result columns RS01...RS25 in the Deter-min

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭353Statisticson | off (Default value: off)Shows the statistics results.Assignmenton | off (Default va

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭354￭￭￭￭￭￭￭￭tiamo 2.1undone with a double-click on the section of the graph or with the context-sensitive men

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭355The display of the measuring points in the table can be defined per windowand per command type in

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭23NoteSignatures 2 can only be deleted if the user belongs to a user group withthe c

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭356￭￭￭￭￭￭￭￭tiamo 2.1Stop command (only Titrando)The running STAT command was quit, then the next command was

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭357NoteWhen the dialog window is opened, those Command type will be selec-ted as standard which appli

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭358￭￭￭￭￭￭￭￭tiamo 2.1For BRC commandsSelectionTime [s] | Measured value | Amount [µg] |Charge [mAs] | Drift [

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭359LabelFreely definable axis label for the x axis. With auto the designation from thefield Size will

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭360￭￭￭￭￭￭￭￭tiamo 2.1Autoscalingon | off (Default value: on)If this option is switched on then all axes in th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭361For MEAS T/Flow commandsSelectionTime [s] | Measured value | Flow [ml/min] | Cal-culated 1...3 | E

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭362￭￭￭￭￭￭￭￭tiamo 2.1Only editable when autoscaling is disabled.Range-1.00E+12 ... +1.00E+12 Default value-1.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭363SmoothingSmoothingon | off (Default value: on)Switches smoothing on/off for the curve.Smoothing fa

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭364￭￭￭￭￭￭￭￭tiamo 2.1Autoscalingon | off (Default value: on)If this option is switched on then all axes in th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭365For MEAS T/Flow commandsSelectionTime [s] | Measured value | Flow [ml/min] | Cal-culated 1...3 | E

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭24￭￭￭￭￭￭￭￭tiamo 2.1￭ timeTime indications must always be made with the aid of the Time( ) func-tion.Entry usin

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭366￭￭￭￭￭￭￭￭tiamo 2.1Selection13 colors | pinkDefault valuepinkSymbolSelection of the symbol for the display

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭3674.8.4.5 Curve properties - OptionsDialog window: Database ▶ Curves ▶ Properties curves # ▶ Option

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭368￭￭￭￭￭￭￭￭tiamo 2.1BackgroundBackground colorSelection of the color for the curve background.Selection13 co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1￭￭￭￭￭￭￭￭3694.8.4.6 Curve properties - Measuring point listDialog window: Database ▶ Curves ▶ Properties curv

5.1 Method - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭370￭￭￭￭￭￭￭￭tiamo 2.15 Method5.1 Method - General5.1.1 Method - Definition Program part: MethodDefinitio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭371further modifications. Methods are stored in the configuration data-base and globally accessible for

5.1 Method - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭372￭￭￭￭￭￭￭￭tiamo 2.15.1.3.2 Method - Menu FileProgram part: MethodNew… Create a new method (see Chapter 5.2

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭373Insert Inserts the content of the clipboard (commands, tracks) above the selected com-mand or on the

5.1 Method - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭374￭￭￭￭￭￭￭￭tiamo 2.1SaveSave the selected method (see Chapter 5.2.6, page 385).CloseClose the selected metho

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭375Split horizontally Splits method window horizontally and display two methods below each other(see Ch

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭25-2.38 yields -2.4-2.45 yields -2.5StatisticsThe mean value, absolute and relative

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭376￭￭￭￭￭￭￭￭tiamo 2.15.2 Method editor5.2.1 Creating new methodMenu item: Method ▶ File ▶ New…With the symbol

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭377NameName of the method.SavedDate and time when the method was saved.UserShort name of the user who s

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭378￭￭￭￭￭￭￭￭tiamo 2.1program; the number of currently opened methods is displayed in the leftupper corner of the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭3795.2.3.1 Display single methodMenu item: Method ▶ View ▶ UnsplitIn the default settings, the most re

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭380￭￭￭￭￭￭￭￭tiamo 2.1SelectionFit to windowAdjust to both height and width of the window.5.2.4 Edit method5.2.4

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭3815.2.4.1.3 Move trackProgram part: Method ▶ Method windowMove track with Drag&DropTo move a trac

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭382￭￭￭￭￭￭￭￭tiamo 2.15.2.4.1.5 Cut trackMenu item: Method ▶ Edit ▶ CutThe selected track is moved to the clipbo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭383The new command is inserted above the selected command after confirmingthe selection with [OK].5.2.4

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭384￭￭￭￭￭￭￭￭tiamo 2.15.2.4.2.6 Insert commandMenu item: Method ▶ Edit ▶ InsertThe commands copied to the clipbo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭3855.2.5 Checking methodMenu item: Method ▶ File ▶ Method checkWith the symbol or menu item File ▶ M

TeachwareMetrohm AGCH-9101 [email protected] documentation is protected by copyright. All rights reserved.Although all the information

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭26￭￭￭￭￭￭￭￭tiamo 2.1The number of significant digits has now been reduced by three to four digitsby omitting th

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭386￭￭￭￭￭￭￭￭tiamo 2.1SavedDate and time when the method was saved.UserShort name of the user who saved the metho

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭387[Save]Save the selected method under the desired method name in the selectedmethod group.The method

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭388￭￭￭￭￭￭￭￭tiamo 2.15.2.8 Print method reportMenu item: Method ▶ File ▶ Print (PDF)…With menu item File ▶ Prin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭3895.3 Managing methods5.3.1 Managing methodsDialog window Method ▶ File ▶ Method manager… ▶ Method m

5.3 Managing methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭390￭￭￭￭￭￭￭￭tiamo 2.1SignedDisplay if and at which level the method has been signed.Selectionno | Level 1 | L

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭391Show signatures…Show all signatures of the selected method (see Chapter 5.3.10.4, page 397).Delete s

5.3 Managing methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭392￭￭￭￭￭￭￭￭tiamo 2.1Method groupSelection of the method group to which the selected methods should bemoved.S

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭3935.3.7 Exporting a methodMenu item: Method ▶ File ▶ Method manager... ▶ Method man-ager ▶ [Edit] ▶ E

5.3 Managing methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭394￭￭￭￭￭￭￭￭tiamo 2.1NoteThe method name must be unique in the whole Client/Server system.Locked methods cann

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭3955.3.10.2 Signature Level 1Dialog window:Database ▶ Determinations ▶ Sign ▶ Signature1... ▶ Signatur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭27Name Syntax DescriptionCommonvariables'CV.Variablename.Variableidentification

5.3 Managing methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭396￭￭￭￭￭￭￭￭tiamo 2.1ReasonSelection from the Default reasons defined in the Security Settings dia-log window

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭397Signature 2 not possible (signature 1 missing)The selected method or determination cannot be signed

5.3 Managing methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭398￭￭￭￭￭￭￭￭tiamo 2.1Signature dateDate and time at which the method was signed.UserShort name of the user wh

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭399[Delete]Delete Signatures 2.NoteSignatures 2 can only be deleted if the user belongs to a user group

5.4 Method groups￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭400￭￭￭￭￭￭￭￭tiamo 2.1[Make current]Restores the selected method version as the current method version. Thiscreat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭401[Delete]Deleting the selected method group.5.4.2 Edit method groups5.4.2.1 Method groups - Propert

5.5 Tracks￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭402￭￭￭￭￭￭￭￭tiamo 2.1NoteThe user group Administrators always has both access rights, i.e. theycannot be disabled.User

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭403PresentationThe individual tracks are arranged side by side in the method window. Thetrack name is d

5.5 Tracks￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭404￭￭￭￭￭￭￭￭tiamo 2.15.5.2.2 Normal trackSubwindow: MethodA normal track is a track that can be created manually by th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭405￭ Parallel running normal trackIf the check box Return immediately in the (see Chapter 5.6.2.3, page

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭28￭￭￭￭￭￭￭￭tiamo 2.1Variable name Description Data type.OVFExceeding limits for methodvariable (Number: 1 = lim

5.5 Tracks￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭406￭￭￭￭￭￭￭￭tiamo 2.15.5.2.4 Series end trackSubwindow: MethodA series end track is a track that can be created manual

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭4075.5.2.5 Exit trackSubwindow: MethodAn exit track is a track that can be created manually with Paste

5.5 Tracks￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭408￭￭￭￭￭￭￭￭tiamo 2.1The error track is executed if the determination is stopped due to an error.In this case the error

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭4095.6 Commands5.6.1 Commands - General5.6.1.1 Definition and PresentationSubwindow: MethodDefinitio

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭410￭￭￭￭￭￭￭￭tiamo 2.1￭ GreenTitration and measurement commands￭ YellowSample Processor and dosing commands￭ BlueAll o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭411￭ CTRLSetting remote output lines.￭ DATABASEStorage of the determination data in data bases.￭ DETDyn

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭412￭￭￭￭￭￭￭￭tiamo 2.1￭ RACKInitialization of the rack attached.￭ RECEIVEWaiting for event messages or status messages

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭4135.6.2 Track commands5.6.2.1 Track commands - OverviewMenu item: Method ▶ Insert ▶ New track...The

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭414￭￭￭￭￭￭￭￭tiamo 2.1Command variablesNo command variables are generated in the method run by the STARTcommand.Method

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭415Workplace viewWorkplace viewSelectionCurrent view | ViewDefault valueCurrent viewCurrent viewIf this

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭29NoteIn the case of variables with Index {x}, the desired number 1…9 must beentered

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭416￭￭￭￭￭￭￭￭tiamo 2.1NoteIn order to make sure that the statistics will really be calculated, the featuremust also be

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭417The text editor with which the application note can be entered or changedis opened with or by doub

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭418￭￭￭￭￭￭￭￭tiamo 2.1TypeSelection of the variable type. This field cannot be edited with variables witha unique type

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭419Check at starton | off (Default value: on)If this option is enabled, the start test will check if th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭420￭￭￭￭￭￭￭￭tiamo 2.1Type = Date/TimeSelection'Date'MessageNoteIs displayed only for method variables of th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭421ActionNoteIs displayed only for method variables of the types Number or Date/Time.Actionon | off (De

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭422￭￭￭￭￭￭￭￭tiamo 2.1Parameter for "Use E-mail template = off"Mail toE-mail address of the recipient.Input2

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭423Command nameName of the command.Input25 charactersLive displayon | off (Default value: on)If this op

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭424￭￭￭￭￭￭￭￭tiamo 2.15.6.2.4 SERIES STARTDialog window: Method ▶ SERIES START ▶ Properties.. ▶ SERIES START 'Co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭425ParametersCommand nameName of the command.Input25 charactersLive displayon | off (Default value: on)

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭30￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription Commands.C0Coefficient c0 of the calibrationcurveCAL Spec.C1Coef

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭426￭￭￭￭￭￭￭￭tiamo 2.1Input25 charactersLive displayon | off (Default value: on)If this option is enabled, then the tr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭427Command variablesThe following command variables are generated in the method run by thecommand START

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭428￭￭￭￭￭￭￭￭tiamo 2.1￭ METCommand for Monotonic Equivalence Point Titrations.￭ (see Chapter 5.6.3.4.1, page 639)Comma

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭429EvaluationEquivalence points EP are determined atuomatically in a similar manner tothat described in

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭430￭￭￭￭￭￭￭￭tiamo 2.1￭ DET UVoltametric measurement with selectable polarization current (measuredquantity voltage U)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭431￭ Additional measured valuesDefinition of additional measured values of other measuring commandswhic

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭432￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.EP{x}.VOLVolume for the endpoint × (1…9) in mL.ETEEnd temperature (te

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭433Identification Description.LP.MEAMeasured value for the last measuring point in themeasuring point l

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭434￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.SVSStart volume slope (volume that was added accordingto the start co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭435Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or exchange unit) wit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭31Identifica-tionDescription Commands.DBLTotal duration for the processing ofthe com

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭436￭￭￭￭￭￭￭￭tiamo 2.1855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSelection of a senso

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭437Stirring rateSetting the stirring rate. The algebraic sign of the stirring rate changes thedirection

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭438￭￭￭￭￭￭￭￭tiamo 2.1SelectionoffDefault valueoffoffThe measured vales will not be applied until after the maximum wa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭439TitrinoRange0.01 ... 150.00 mL/minSelectionmaximumDefault valuemaximumStart measured valueNoteIs dis

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭440￭￭￭￭￭￭￭￭tiamo 2.1Dosing rateSpeed at which the start volume is added until the start slope is reached.The maximum

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭441fastFor less critical rapid titrations.UserEditing the individual titration parameters which affect

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭442￭￭￭￭￭￭￭￭tiamo 2.1elapsed. If the waiting time has not been newly entered then a waiting timethat is suitable for

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭443if the change of direction in the potential jump region is very abrupt, asotherwise it is easy to ad

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭444￭￭￭￭￭￭￭￭tiamo 2.15.6.3.2.2.5 DET pH - Stop conditionsTab: Method ▶ DET pH ▶ Properties... ▶ Stop conditionsComma

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭445SelectionoffVolume after EPWhen the number of equivalence points defined under Stop EP has beenfound

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭32￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription Commands.EP{x}.MEAMeasured value for the endpoint x(1…9) in the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭446￭￭￭￭￭￭￭￭tiamo 2.1Potentiometric evaluationSelectionEvaluation without window | Evaluation withmeasured value wind

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭447greatestOnly the equivalence point with the greatest ERC value, i.e. the steepestjump, will be recog

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭448￭￭￭￭￭￭￭￭tiamo 2.15.6.3.2.2.7 DET pH - Additional evaluationsTab: Method ▶ DET pH ▶ Properties... ▶ Additional ev

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭449Minimum evaluationMinimum evaluationon | off (Default value: off)If this option is enabled, then the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭450￭￭￭￭￭￭￭￭tiamo 2.1related to the total measured value alteration, even small changes in themeasured value can be e

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭451Window = Measured value pHRange-20.0 ... 20.0 pHDefault value20.0 pHWindow = VolumeRange0.00000 ...

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭452￭￭￭￭￭￭￭￭tiamo 2.1Range-20.000 ... 20.000 Default value20.000 5.6.3.2.2.8 DET pH - Additional measured valuesTab:

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭453[New]Opens the dialog window External measured value # in which theparameters for the external measu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭454￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Selectionfirst | greatest | last | ascending | descendingDefault valuefirstfirstOnl

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭455EP criterionCriterion for the recognition of endpoints. Endpoints whose discovered ERCvalue is small

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭33Identifica-tionDescription Commands.FP{x}.DMEMeasured value differential for thefi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭456￭￭￭￭￭￭￭￭tiamo 2.1TimeRange0.0 ... 999999.9 sVolumeRange0.00000 ... 9999.99 mL5.6.3.2.3 DET U5.6.3.2.3.1 DET U -

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭457￭ Additional measured valuesDefinition of additional measured values of other measuring commandswhic

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭458￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.EP{x}.TIMTime in s until the endpoint × (1…9) is reached.EP{x}.VOLVol

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭459Identification Description.LP.EXxExternal value × (1...3) for the last measuring point ofthe measuri

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭460￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.SVMStart volume measured value (volume which was addedaccording to th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭461Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or exchange unit) wit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭462￭￭￭￭￭￭￭￭tiamo 2.1855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSelection of a senso

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭463Stirring rateSetting the stirring rate. The algebraic sign of the stirring rate changes thedirection

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭464￭￭￭￭￭￭￭￭tiamo 2.1SelectionoffDefault valueoffoffThe measured vales will not be applied until after the maximum wa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭465TitrinoRange0.01 ... 150.00 mL/minSelectionmaximumDefault valuemaximumStart measured valueNoteIs dis

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭34￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription Commands.GP.MEAMeasured value for the Gran end-point in the unit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭466￭￭￭￭￭￭￭￭tiamo 2.1Dosing rateSpeed at which the start volume is added until the start slope is reached.The maximum

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭467fastFor less critical rapid titrations.UserEditing the individual titration parameters which affect

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭468￭￭￭￭￭￭￭￭tiamo 2.1elapsed. If the waiting time has not been newly entered then a waiting timethat is suitable for

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭469if the change of direction in the potential jump region is very abrupt, asotherwise it is easy to ad

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭470￭￭￭￭￭￭￭￭tiamo 2.15.6.3.2.3.5 DET U - Stop conditionsTab: Method ▶ DET U ▶ Properties... ▶ Stop conditionsCommand

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭471SelectionoffVolume after EPWhen the number of equivalence points defined under Stop EP has beenfound

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭472￭￭￭￭￭￭￭￭tiamo 2.1Potentiometric evaluationSelectionEvaluation without window | Evaluation withmeasured value wind

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭473greatestOnly the equivalence point with the greatest ERC value, i.e. the steepestjump, will be recog

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭474￭￭￭￭￭￭￭￭tiamo 2.15.6.3.2.3.7 DET U - Additional evaluationsTab: Method ▶ DET U ▶ Properties... ▶ Additional eval

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭475Minimum evaluationMinimum evaluationon | off (Default value: off)If this option is enabled, then the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭35Identifica-tionDescription Commands.LP.CAxCalculated value x (1…3) for the lastmea

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭476￭￭￭￭￭￭￭￭tiamo 2.1related to the total measured value alteration, even small changes in themeasured value can be e

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭477Window = Measured valueRange-2000.0 ... 2000.0 mVDefault value2000.0 mVWindow = VolumeRange0.00000 .

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭478￭￭￭￭￭￭￭￭tiamo 2.15.6.3.2.3.8 DET U - Additional measured valuesTab: Method ▶ DET U ▶ Properties... ▶ Additional

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭479[Properties]Opens the dialog window External measured value # in which theparameters for the externa

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭480￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0 ... 200 Default value5 EP recognitionFilter for the recognition of equivalen

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭481Titrando, 855Range0.00000 ... 9999.99 mLDefault value9999.99 mLEP criterionCriterion for the recogni

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭482￭￭￭￭￭￭￭￭tiamo 2.1Measured valueRange-2000.0 ... 2000.0 mVTimeRange0.0 ... 999999.9 sVolumeRange0.00000 ... 9999.9

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭483￭ Additional evaluationsDefinition of additional methods for the evaluation of the titration curves.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭484￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.ETEEnd temperature (temperature following processing ofthe command) i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭485Identification Description.LP.MEAMeasured value for the last measuring point in themeasuring point l

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1￭￭￭￭￭￭￭￭IIITable of contents1 Introduction 11.1 Welcome to tiamo ...

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭36￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription Commands.LP.QTYMeasured value (water) for the lastmeasuring poin

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭486￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.SVTTotal start volume (volume that was added in depend-ence on all th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭487TitrandoSelection1 | 2 | 3 | 4Default value1855Selection1 | 2 | 3Default value1TitrinoSelectioninter

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭488￭￭￭￭￭￭￭￭tiamo 2.1Measuring inputSelection of the measuring input to which the sensor is connected.TitrandoSelecti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭489continuousA temperature sensor must be connected. The temperature will then bemeasured continuously.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭490￭￭￭￭￭￭￭￭tiamo 2.15.6.3.2.4.3 DET Ipol - Start conditionsTab: Method ▶ DET Ipol ▶ Properties... ▶ Start condition

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭491Range0 ... 999999 sDefault value1 sStart volumeStart volumeVolume to be added before the start of th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭492￭￭￭￭￭￭￭￭tiamo 2.1Dosing rateSpeed at which the start volume is added until the start slope is reached.The maximum

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭4935.6.3.2.4.4 DET Ipol - Titration parametersTab: Method ▶ DET Ipol ▶ Properties... ▶ Titration param

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭494￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0.1 ... 999.0 mV/minDefault value20.0 (slow), 50.0 (optimal), 80.0 (fast) mV/m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭495Dosing of incrementsNoteThe following parameters will be displayed only if the User option isselecte

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭37Identifica-tionDescription Commands.MA.TEMTemperature for the maximummeasured valu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭496￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0.01 ... 166.00 mL/minSelectionmaximumDefault valuemaximumTitrinoRange0.01 ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭497Titrando, 855Range0.00000 ... 9999.99 mLDefault value100,000 mLSelectionoffTitrinoRange0.000 ... 999

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭498￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with which the dos

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭499Evaluation with measured value window (Upol)With this option set, up to 9 regions (windows) can be d

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭500￭￭￭￭￭￭￭￭tiamo 2.1descendingOnly equivalence points with a negative slope of the titration curve willbe recognized

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭501The following additional methods for evaluation of titration curves can beactivated and defined on t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭502￭￭￭￭￭￭￭￭tiamo 2.1Maximum evaluationMaximum evaluationon | off (Default value: off)If this option is enabled, then

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭503Range2 ... 20 Default value5 WindowA range (window) can be defined on the measured value axis, on th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭504￭￭￭￭￭￭￭￭tiamo 2.1Gran evaluationNoteThis evaluation method is possible only with Titrando and 855.Gran evaluation

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭505Additional calculated measured valuesAdditional calculated measured valueson | off (Default value: o

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭38￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription Commands.MR.MRSStandard deviation for mean dosingrate for the wh

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭506￭￭￭￭￭￭￭￭tiamo 2.15.6.3.2.4.9 DET Ipol - Measured value windowDialog window: Method ▶ DET Ipol ▶ Properties... ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭507Titrando, 855Selectionfirst | greatest | last | ascending | descendingDefault valuefirstfirstOnly th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭508￭￭￭￭￭￭￭￭tiamo 2.1EP criterionCriterion for the recognition of endpoints. Endpoints whose discovered ERCvalue is s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭509TimeRange0.0 ... 999999.9 sVolumeRange0.00000 ... 9999.99 mL5.6.3.2.5 DET Upol5.6.3.2.5.1 DET Upol

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭510￭￭￭￭￭￭￭￭tiamo 2.1￭ Additional measured valuesDefinition of additional measured values of other measuring commands

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭511.ETEEnd temperature (temperature following processing ofthe command) in °C.EVTEnd volume (total dose

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭512￭￭￭￭￭￭￭￭tiamo 2.1.LP.TEMTemperature for the last measuring point of the meas-uring point list in °C.LP.TIMTime in

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭5135.6.3.2.5.2 DET Upol - General/HardwareTab: Method ▶ DET Upol ▶ Properties... ▶ General/HardwareCom

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭514￭￭￭￭￭￭￭￭tiamo 2.1855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectioninternal D0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭515U(pol)The polarization voltage is the potential applied to the polarized electrodeduring an amperome

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭39Identifica-tionDescription Commands.RE{x}.DRCCorrelation coefficient for meandosin

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭516￭￭￭￭￭￭￭￭tiamo 2.1offNo stirrer will be used.Stirring rateSetting the stirring rate. The algebraic sign of the sti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭517Titrando, 855Range0.01 ... 99.90 µA/minDefault value20.00 (slow), 50.00 (optimal), 80.00 (fast) µA/m

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭518￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange0.00 ... 999.99 mLDefault value0.00 mLDosing rateSpeed at which the start volume is

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭519Start slopeNoteIs displayed only for Titrando and 855.Start slopeWhen the start slope is reached the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭520￭￭￭￭￭￭￭￭tiamo 2.1Titration rateTitration rateThe three predefined sets of parameters can be selected for the titr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭521TitrinoRange0.05 ... 99.90 µA/minDefault value20.00 (slow), 50.00 (optimal), 80.00 (fast) µA/minSele

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭522￭￭￭￭￭￭￭￭tiamo 2.1Measuring point densityA small value means small volume increments, i.e. a high measuring pointd

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭523SelectionmaximumDefault valuemaximumTemperatureTemperatureManually entered titration temperature. If

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭524￭￭￭￭￭￭￭￭tiamo 2.1Stop measured valueStops when the preset value for a measuring point has been exceeded ornot ach

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭525SelectionmaximumDefault valuemaximum5.6.3.2.5.6 DET Upol - Potentiometric evaluationTab: Method ▶ D

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭40￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription Commands.STYType of stop with which the com-mand was stopped: 1

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭526￭￭￭￭￭￭￭￭tiamo 2.1EP recognitionFilter for the recognition of equivalence points:TitrinoSelectionall | greatest |

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭527[Delete]Deletes the window selected in the table.Evaluation with volume window (mL)[New]Opens the di

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭528￭￭￭￭￭￭￭￭tiamo 2.1[Properties]Opens the dialog window Fix endpoint evaluation # to edit the fixedendpoint selected

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭529Break-point evaluationon | off (Default value: off)A break-point evaluation is used to determine sha

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭530￭￭￭￭￭￭￭￭tiamo 2.1Window = TimeRange0 ... 999999 sDefault value0 sUpper limitValue for the upper limit of the wind

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭531Upper limitValue for the upper limit of the Gran evaluation range.Range-200.0 ... 200.0 µADefault va

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭532￭￭￭￭￭￭￭￭tiamo 2.1can also be displayed in curves under the designation Extern 1…3 and usedin formulas as variable

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭533Titrando, 855Selectionfirst | greatest | last | ascending | descendingDefault valuefirstfirstOnly th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭534￭￭￭￭￭￭￭￭tiamo 2.1EP criterionCriterion for the recognition of endpoints. Endpoints whose discovered ERCvalue is s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭535TimeRange0.0 ... 999999.9 sVolumeRange0.00000 ... 9999.99 mL5.6.3.3 MET5.6.3.3.1 MET - OverviewMen

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭41Identifica-tionDescription Commands.TC.MAXMaximum temperature coefficientof the co

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭536￭￭￭￭￭￭￭￭tiamo 2.1VEP = EP volume, V0 = total volume added before ∆n, ∆V = volume incre-ment,ρ = interpolation fac

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭537ParametersThe parameters for the command MET pH are configured in the following7 tabs:￭ General/Hard

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭538￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.DSCTime for processing all start conditions s.EMEEnd measured value (

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭539Identification Description.HP{x}.MEAMeasured value for the HNP × (1…9) in mV (HNP = halfneutralizati

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭540￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.MI.TIMTime for the minimum measured value in s.MI.VOLVolume for minim

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭541Selection'Device name' | not definedDefault valuenot definednot definedIn this case, the d

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭542￭￭￭￭￭￭￭￭tiamo 2.1of the working life, the validity of the titer and the GLP test interval for theselected solutio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭543offThe temperature will not be measured. The temperature entered man-ually under Temperature on the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭544￭￭￭￭￭￭￭￭tiamo 2.1Initial measured valueNoteIs displayed only for Titrando and 855.The initial measured value is d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭545Titrando, 855Range0.00000 ... 9999.99 mLDefault value0.00000 mLTitrinoRange0.00 ... 999.99 mLDefault

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭42￭￭￭￭￭￭￭￭tiamo 2.1Syntax'RS.Result name.Variable identification'Examples: 'RS.RS01.VAL' (

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭546￭￭￭￭￭￭￭￭tiamo 2.1SelectionmaximumStart slopeNoteIs displayed only for Titrando and 855.Start slopeWhen the start

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭547Titration rateTitration rateThe three predefined sets of parameters can be selected for the titratio

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭548￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange0.5 ... 999.0 mV/minDefault value20.0 (slow), 50.0 (optimal), 80.0 (fast) mV/minSele

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭549Volume incrementSmall volume increments are used for the determination of blank values orfor very as

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭550￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange-170.0 ... 500.0 °CDefault value25.0 °C5.6.3.3.2.5 MET pH - Stop conditionsTab: Met

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭551Stop EPThe titration is stopped when the specified number of equivalence pointshas been found.Range1

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭552￭￭￭￭￭￭￭￭tiamo 2.15.6.3.3.2.6 MET pH - Potentiometric evaluationTab: Method ▶ MET pH ▶ Properties... ▶ Potentiome

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭553EP recognitionFilter for the recognition of equivalence points:TitrinoSelectionall | greatest | last

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭554￭￭￭￭￭￭￭￭tiamo 2.1[Properties]Opens the dialog window Volume window # in which the parameters forthe selected wind

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭555pK/HNP evaluationpK/HNP evaluationon | off (Default value: off)If this option is enabled, then the p

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭43Available determination variablesVariable name Description DatatypeDURDuration of

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭556￭￭￭￭￭￭￭￭tiamo 2.1Break-point evaluationon | off (Default value: off)A break-point evaluation is used to determine

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭557Window = TimeRange0 ... 999999 sDefault value0 sUpper limitValue for the upper limit of the window.W

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭558￭￭￭￭￭￭￭￭tiamo 2.1Lower limit pHValue for the lower limit of the Gran evaluation range.Range-20.000 ... 20.000 Def

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭559Additional external measured valuesAdditional external measured valueson | off (Default value: off)I

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭560￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0.1 ... 9.99 Default value0.50 EP recognitionFilter for the recognition of equ

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭561Titrando, 855Range0.00000 ... 9999.99 mLDefault value9999.99 mLEP criterion pHCriterion for the reco

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭562￭￭￭￭￭￭￭￭tiamo 2.1Fix valueValue of the fix endpoint.Measured valueRange-20.000 ... 20.000 pHTimeRange0.0 ... 9999

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭563￭ Potentiometric evaluationParameters for the potentiometric evaluation of titration curves.￭ Additi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭564￭￭￭￭￭￭￭￭tiamo 2.1.EP{x}.MEP Quantity of endpoints in the window × (1…9); 1 = 1endpoint, 2 = 2 or more endpoints,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭565.ITEInitial temperature (temperature before start conditionsare processed) in °C.LP.CAxCalculated va

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭44￭￭￭￭￭￭￭￭tiamo 2.1Variable name Description DatatypeSTOIndication whether the determination has been stopped

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭566￭￭￭￭￭￭￭￭tiamo 2.1.STYType of stop with which the command was stopped:1 = normal;0 = manual or after error.SVAStar

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭567Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or exchange unit) wit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭568￭￭￭￭￭￭￭￭tiamo 2.1855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSelection of a senso

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭569Stirring rateSetting the stirring rate. The algebraic sign of the stirring rate changes thedirection

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭570￭￭￭￭￭￭￭￭tiamo 2.1SelectionoffDefault valueoffoffThe measured vales will not be applied until after the maximum wa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭571TitrinoRange0.01 ... 150.00 mL/minSelectionmaximumDefault valuemaximumStart measured valueNoteIs dis

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭572￭￭￭￭￭￭￭￭tiamo 2.1Dosing rateSpeed at which the start volume is added until the start slope is reached.The maximum

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭573fastFor less critical rapid titrations.UserEditing the individual titration parameters which affect

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭574￭￭￭￭￭￭￭￭tiamo 2.1elapsed. If the waiting time has not been newly entered then a waiting timethat is suitable for

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭575Titrando, 855Range0.01 ... 166.00 mL/minSelectionmaximumDefault valuemaximumTitrinoRange0.01 ... 150

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭45Overview of the operators and functionsOperators FunctionsArithmetic:￭ Addition (+

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭576￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0.00000 ... 9999.99 mLDefault value100,000 mLSelectionoffTitrinoRange0.000 ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭577Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with which the dosing

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭578￭￭￭￭￭￭￭￭tiamo 2.1Evaluation with measured value window (U)With this option set, up to 9 regions (windows) can be

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭579descendingOnly equivalence points with a negative slope of the titration curve willbe recognized.off

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭580￭￭￭￭￭￭￭￭tiamo 2.1Fix endpoint evaluationFix endpoint evaluationon | off (Default value: off)If this option is ena

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭581Minimum evaluationMinimum evaluationon | off (Default value: off)If this option is enabled, then the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭582￭￭￭￭￭￭￭￭tiamo 2.1related to the total measured value alteration, even small changes in themeasured value can be e

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭583Window = Measured valueRange-2000.0 ... 2000.0 mVDefault value2000.0 mVWindow = VolumeRange0.00000 .

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭584￭￭￭￭￭￭￭￭tiamo 2.15.6.3.3.3.8 MET U - Additional measured valuesTab: Method ▶ MET U ▶ Properties... ▶ Additional

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭585[Properties]Opens the dialog window External measured value # in which theparameters for the externa

Table of contents￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭IV￭￭￭￭￭￭￭￭tiamo 2.12.4.5 Molar mass calculator ... 782

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭46￭￭￭￭￭￭￭￭tiamo 2.12.4.4.2 Arithmetical operators2.4.4.2.1 AdditionDialog window: Formula editor ▶ Operators

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭586￭￭￭￭￭￭￭￭tiamo 2.1EP recognitionFilter for the recognition of equivalence points:Titrando, 855Selectionfirst | gre

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭587EP criterionCriterion for the recognition of endpoints. Endpoints whose discovered ERCvalue is small

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭588￭￭￭￭￭￭￭￭tiamo 2.1TimeRange0.0 ... 999999.9 sVolumeRange0.00000 ... 9999.99 mL5.6.3.3.4 MET Ipol5.6.3.3.4.1 MET

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭589￭ Additional measured valuesDefinition of additional measured values of other measuring commandswhic

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭590￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.ETEEnd temperature (temperature following processing ofthe command) i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭591Identification Description.LP.EXxExternal value × (1...3) for the last measuring point ofthe measuri

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭592￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.SVSStart volume slope (volume that was added accordingto the start co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭593Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or exchange unit) wit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭594￭￭￭￭￭￭￭￭tiamo 2.1855, 888Selection1Default value1SensorSelection of a sensor of type Metal electrode from the sen

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭595offThe temperature will not be measured. The temperature entered man-ually under Temperature on the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭472.4.4.2.2 SubtractionDialog window: Formula editor ▶ Operators/FunctionsSyntaxOpe

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭596￭￭￭￭￭￭￭￭tiamo 2.1Initial measured valueNoteIs displayed only for Titrando and 855.The initial measured value is d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭597Titrando, 855Range0.00000 ... 9999.99 mLDefault value0.00000 mLTitrinoRange0.00 ... 999.99 mLDefault

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭598￭￭￭￭￭￭￭￭tiamo 2.1SelectionmaximumStart slopeNoteIs displayed only for Titrando and 855.Start slopeWhen the start

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭599Titration rateThe three predefined sets of parameters can be selected for the titrationrate: slow, o

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭600￭￭￭￭￭￭￭￭tiamo 2.1offMeasured value acceptance will take place after the maximum waitingtime has elapsed.Min. wait

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭601as the measured value alterations between two measuring points are thenof the same order of magnitud

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭602￭￭￭￭￭￭￭￭tiamo 2.15.6.3.3.4.5 MET Ipol - Stop conditionsTab: Method ▶ MET Ipol ▶ Properties... ▶ Stop conditionsC

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭603SelectionoffVolume after EPWhen the number of equivalence points defined under Stop EP has beenfound

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭604￭￭￭￭￭￭￭￭tiamo 2.1Potentiometric evaluationSelectionEvaluation without window | Evaluation withmeasured value wind

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭605allAll equivalence points will be recognized.greatestOnly the equivalence point with the greatest ER

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭48￭￭￭￭￭￭￭￭tiamo 2.1ExamplesOperand1 Operand2 Result Example RemarkOperands of the same type:Number Number Numb

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭606￭￭￭￭￭￭￭￭tiamo 2.1[Delete]Deletes the window selected in the table.5.6.3.3.4.7 MET Ipol - Additional evaluationsT

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭607Threshold valueThe evaluation of the minimum begins as soon as the slope of the curveexceeds the set

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭608￭￭￭￭￭￭￭￭tiamo 2.1SlopeMinimum difference between the slope before and after the break-point.The smaller the diffe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭609Window = TimeRange0 ... 999999 sDefault value999999 sGran evaluationNoteThis evaluation method is po

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭610￭￭￭￭￭￭￭￭tiamo 2.1Additional calculated measured valuesAdditional calculated measured valueson | off (Default valu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭6115.6.3.3.4.9 MET Ipol - Measured value windowDialog window: Method ▶ MET Ipol ▶ Properties... ▶ Pote

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭612￭￭￭￭￭￭￭￭tiamo 2.1firstOnly the first endpoint to be found will be recognized.greatestOnly the endpoint with the g

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭613EP recognitionFilter for the recognition of equivalence points:Titrando, 855Selectionfirst | greates

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭614￭￭￭￭￭￭￭￭tiamo 2.15.6.3.3.5 MET Upol5.6.3.3.5.1 MET Upol - OverviewDialog window: Method ▶ MET Upol ▶ Properties

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭615Identification Description.BP{x}.DMEMeasured value differential for the break point × (1…9).BP{x}.ME

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭49Operand1 Operand2 Result Example RemarkOperand of different type: The operand whic

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭616￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.FP{x}.DMEMeasured value differential for the fixed endpoint ×(1…9).FP

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭617Identification Description.LP.TIMTime in s until the last measuring point in the measuringpoint list

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭618￭￭￭￭￭￭￭￭tiamo 2.15.6.3.3.5.2 MET Upol - General/HardwareTab: Method ▶ MET Upol ▶ Properties... ▶ General/Hardwar

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭619855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectioninternal D0 | ex

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭620￭￭￭￭￭￭￭￭tiamo 2.1U(pol)The polarization voltage is the potential applied to the polarized electrodeduring an ampe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭621offNo stirrer will be used.Stirring rateSetting the stirring rate. The algebraic sign of the stirrin

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭622￭￭￭￭￭￭￭￭tiamo 2.1Measured value driftThe measured value is only accepted if the drift is less than the value ente

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭623Titrando, 855Range0.01 ... 166.00 mL/minSelectionmaximumDefault valuemaximumTitrinoRange0.01 ... 150

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭624￭￭￭￭￭￭￭￭tiamo 2.1Start slopeWhen the start slope is reached the dosing of the start volume is stoppedand the titr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭625slowFor titrations in which the finest details are also to be visible. This couldhowever also lead t

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭50￭￭￭￭￭￭￭￭tiamo 2.1Operand1 Operand2 Result Example RemarkTime Number NumberTime(1999;10;7) ^ 2.5 =25347984787

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭626￭￭￭￭￭￭￭￭tiamo 2.1has elapsed, even if the signal drift has already been reached. The drift con-tinues to be check

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭627TitrinoRange0.001 ... 9.999 mLDefault value0.05 (slow), 0.10 (optimal), 0.20 (fast) mLDosing rateSpe

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭628￭￭￭￭￭￭￭￭tiamo 2.1Conditions for stopping the titration. If more than one stop condition is ineffect at the same t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭629Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with which the dosing

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭630￭￭￭￭￭￭￭￭tiamo 2.1Evaluation with measured value window (Upol)With this option set, up to 9 regions (windows) can

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭631descendingOnly equivalence points with a negative slope of the titration curve willbe recognized.off

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭632￭￭￭￭￭￭￭￭tiamo 2.1The following additional methods for evaluation of titration curves can beactivated and defined

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭633Maximum evaluationMaximum evaluationon | off (Default value: off)If this option is enabled, then the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭634￭￭￭￭￭￭￭￭tiamo 2.1Range2 ... 20 Default value5 WindowA range (window) can be defined on the measured value axis, o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭635Gran evaluationNoteThis evaluation method is possible only with Titrando and 855.Gran evaluationon |

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭51Oper-and1Oper-and2Result Example RemarkNumber Text Number1.2 AND "1.2" -

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭636￭￭￭￭￭￭￭￭tiamo 2.1Additional calculated measured valuesAdditional calculated measured valueson | off (Default valu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭6375.6.3.3.5.9 MET Upol - Measured value windowDialog window: Method ▶ MET Upol ▶ Properties... ▶ Pote

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭638￭￭￭￭￭￭￭￭tiamo 2.1descendingOnly endpoints with a negative slope of the titration curve will be rec-ognized.5.6.3.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭639greatestOnly the endpoint with the greatest ERC value, i.e. the steepest jump,will be recognized.las

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭640￭￭￭￭￭￭￭￭tiamo 2.1or after a waiting period. The volume that has been added when the end-point is reached gives th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭641NoteThis command is used for rapid routine determinations when the endpointdoes not change throughou

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭642￭￭￭￭￭￭￭￭tiamo 2.15.6.3.4.3 SET pH5.6.3.4.3.1 SET pH - OverviewDialog window: Method ▶ SET pH ▶ Properties... ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭643￭ Additional measured valuesDefinition of additional measured values of other measuring commandswhic

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭644￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.ETEEnd temperature (temperature following processing ofthe command) i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭645Identification Description.MA.VOLVolume with maximum measured value in mL.MI.MEAMinimum measured val

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭52￭￭￭￭￭￭￭￭tiamo 2.1Operand1 Operand2 Result Example RemarkNumber Number Number5 OR 4 --> 14 OR 0 --> 1Nu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭646￭￭￭￭￭￭￭￭tiamo 2.1Selection'Device name' | not definedDefault valuenot definednot definedIn this case, t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭647of the working life, the validity of the titer and the GLP test interval for theselected solution.Se

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭648￭￭￭￭￭￭￭￭tiamo 2.1offThe temperature will not be measured. The temperature entered man-ually under Temperature on

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭649Initial measured valueNoteIs displayed only for Titrando and 855.The initial measured value is deter

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭650￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 719, 720, 736, 751, 758, 785, 794, 798, 799Range0 ... 999999 sDefault value0 sStart vo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭6515.6.3.4.3.4 SET pH - Control parametersTab: Method ▶ SET pH ▶ Properties... ▶ Control parametersCom

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭652￭￭￭￭￭￭￭￭tiamo 2.1ControlNoteWill be displayed only if the User option is selected in the Titrationrate list box.D

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭653Range0.01 ... 9999.00 µL/minDefault value5.00 (slow), 25.00 (optimal), 50.00(fast) µL/minStop criter

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭654￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange0 ... 999 sDefault value10 sSelectioninf.Stop timeThe titration is stopped if the st

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭6555.6.3.4.3.5 SET pH - Titration parametersTab: Method ▶ SET pH ▶ Properties... ▶ Titration parameter

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭53The operands can be entered either directly or as a variable and can be ofthe type

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭656￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange-170.0 ... 500.0 °CDefault value25.0 °CTime interval measuring pointTime interval fo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭657Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with which the dosing

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭658￭￭￭￭￭￭￭￭tiamo 2.1Drift correctionIf this parameter is set to automatic or manual the drift correction ( = Driftva

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭659Range0 ... 999 sDefault value0 sSample addition timeWaiting time between stop of conditioning and st

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭660￭￭￭￭￭￭￭￭tiamo 2.1Moves the selected line up (changes the sequence).Moves the selected line down (changes the sequ

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭6615.6.3.4.3.9 SET pH - Additional measured valuesTab: Method ▶ SET pH ▶ Properties... ▶ Additional me

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭662￭￭￭￭￭￭￭￭tiamo 2.1[Properties]Opens the dialog window External measured value # in which theparameters for the ext

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭663AppearanceThe command has the following appearance:without conditioning with conditioningParametersT

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭664￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.CBY Command status; 1 = Conditioning activated, 0 =Conditioning deact

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭665Identification Description.FP{x}.TIMTime in s until the fixed endpoint × (1…9) is reached.FP{x}.VOLV

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭54￭￭￭￭￭￭￭￭tiamo 2.12.4.4.4.2 Greater thanDialog window: Formula editor ▶ Operators/FunctionsSyntaxOperand1 &g

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭666￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.SLOElectrode slope of the sensor used for the command (inmV for ISE s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭667If the option not defined is selected as Device name, any device types ordevice groups which are abl

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭668￭￭￭￭￭￭￭￭tiamo 2.1SensorMeasuring inputSelection of the measuring input to which the sensor is connected.TitrandoS

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭669StirrerStirrerSelection of the stirrer.Titrando, 855Selection1 | 2 | 3 | 4 | offoffNo stirrer will b

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭670￭￭￭￭￭￭￭￭tiamo 2.1Initial measured valueNoteIs displayed only for Titrando and 855.The initial measured value is d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭671Titrando, 719, 720, 736, 751, 758, 785, 794, 798, 799Range0 ... 999999 sDefault value0 sStart volume

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭672￭￭￭￭￭￭￭￭tiamo 2.15.6.3.4.4.4 SET U - Control parametersTab: Method ▶ SET U ▶ Properties... ▶ Control parametersC

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭673ControlNoteWill be displayed only if the User option is selected in the Titrationrate list box.Contr

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭674￭￭￭￭￭￭￭￭tiamo 2.1Range0.01 ... 9999.00 µL/minDefault value5.00 (slow), 25.00 (optimal), 50.00(fast) µL/minStop cr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭675TitrinoRange0 ... 999 sDefault value10 sSelectioninf.Stop timeThe titration is stopped if the stop t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭552.4.4.4.3 Greater than or equal toDialog window: Formula editor ▶ Operators/Funct

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭676￭￭￭￭￭￭￭￭tiamo 2.15.6.3.4.4.5 SET U - Titration parametersTab: Method ▶ SET U ▶ Properties... ▶ Titration paramet

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭677TitrinoRange-170.0 ... 500.0 °CDefault value25.0 °CTime interval measuring pointTime interval for en

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭678￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with which the dos

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭679Drift correctionIf this parameter is set to automatic or manual the drift correction ( = Driftvalue

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭680￭￭￭￭￭￭￭￭tiamo 2.1Range0 ... 999 sDefault value0 sSample addition timeWaiting time between stop of conditioning an

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭681Moves the selected line up (changes the sequence).Moves the selected line down (changes the sequence

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭682￭￭￭￭￭￭￭￭tiamo 2.15.6.3.4.4.9 SET U - Additional measured valuesTab: Method ▶ SET U ▶ Properties... ▶ Additional

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭683[Properties]Opens the dialog window External measured value # in which theparameters for the externa

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭684￭￭￭￭￭￭￭￭tiamo 2.1AppearanceThe command has the following appearance:without conditioning with conditioningParamet

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭685Identification Description.COK Command status; 1 = Condition requirement ful-filled, 0 = Condition r

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1￭￭￭￭￭￭￭￭V3.8.3 Live display - Application note ... 1683.8.4

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭56￭￭￭￭￭￭￭￭tiamo 2.12.4.4.4.4 Less than Dialog window: Formula editor ▶ Operators/FunctionsSyntaxOperand1 <

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭686￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.IMEInitial measured value (measured value before startconditions are

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭687Identification Description.STEStart temperature (temperature after processing of thestart conditions

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭688￭￭￭￭￭￭￭￭tiamo 2.1Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or exchange unit)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭689855, 888Selection1Default value1SensorSelection of a sensor of type Metal electrode from the sensors

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭690￭￭￭￭￭￭￭￭tiamo 2.1offThe temperature will not be measured. The temperature entered man-ually under Temperature on

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭691Initial measured valueNoteIs displayed only for Titrando and 855.The initial measured value is deter

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭692￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 719, 720, 736, 751, 758, 785, 794, 798, 799Range0 ... 999999 sDefault value0 sStart vo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭6935.6.3.4.5.4 SET Ipol - Control parametersTab: Method ▶ SET Ipol ▶ Properties... ▶ Control parameter

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭694￭￭￭￭￭￭￭￭tiamo 2.1ControlNoteWill be displayed only if the User option is selected in the Titrationrate list box.C

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭695Range0.01 ... 9999.00 µL/minDefault value5.00 (slow), 25.00 (optimal), 50.00(fast) µL/minStop criter

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭572.4.4.4.5 Less than or equal to Dialog window: Formula editor ▶ Operators/Functio

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭696￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange0 ... 999 sDefault value10 sSelectioninf.Stop timeThe titration is stopped if the st

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭6975.6.3.4.5.5 SET Ipol - Titration parametersTab: Method ▶ SET Ipol ▶ Properties... ▶ Titration param

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭698￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange-170.0 ... 500.0 °CDefault value25.0 °CTime interval measuring pointTime interval fo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭699Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with which the dosing

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭700￭￭￭￭￭￭￭￭tiamo 2.1Drift correctionIf this parameter is set to automatic or manual the drift correction ( = Driftva

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭701Range0 ... 999 sDefault value0 sSample addition timeWaiting time between stop of conditioning and st

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭702￭￭￭￭￭￭￭￭tiamo 2.1Moves the selected line up (changes the sequence).Moves the selected line down (changes the sequ

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭7035.6.3.4.5.9 SET Ipol - Additional measured valuesTab: Method ▶ SET Ipol ▶ Properties... ▶ Additiona

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭704￭￭￭￭￭￭￭￭tiamo 2.1[Properties]Opens the dialog window External measured value # in which theparameters for the ext

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭705AppearanceThe command has the following appearance:without conditioning with conditioningParametersT

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭58￭￭￭￭￭￭￭￭tiamo 2.12.4.4.4.6 Not equal to Dialog window: Formula editor ▶ Operators/FunctionsSyntaxOperand1 &

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭706￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.COK Command status; 1 = Condition requirement ful-filled, 0 = Conditi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭707Identification Description.IMEInitial measured value (measured value before startconditions are proc

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭708￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.SMEStart measured value (measured value after processingthe start con

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭709SelectionDevice types | TitrandoDefault valueTitrandoDosing deviceDosing deviceSelection of the numb

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭710￭￭￭￭￭￭￭￭tiamo 2.1TitrandoSelection1 | 2Default value1855, 888Selection1Default value1SensorSelection of a sensor

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭711automaticIf a temperature sensor is connected then the temperature will be meas-ured continuously. O

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭712￭￭￭￭￭￭￭￭tiamo 2.15.6.3.4.6.3 SET Upol - Start conditionsTab: Method ▶ SET Upol ▶ Properties... ▶ Start condition

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭713Range0 ... 999999 sDefault value1 sPause 1Pause 1Waiting time, e.g. until the electrode has settled

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭714￭￭￭￭￭￭￭￭tiamo 2.1Pause 2Pause 2Waiting time, e.g. for the electrode to settle down after the start or a reac-tion

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭715UserEditing the individual titration parameters which affect the titration rate.ControlNoteWill be d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭592.4.4.5 Arithmetical functions2.4.4.5.1 Exponential functionDialog window: Formu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭716￭￭￭￭￭￭￭￭tiamo 2.1Range0.01 ... 9999.00 µL/minDefault value5.00 (slow), 25.00 (optimal), 50.00(fast) µL/minStop cr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭717TitrinoRange0 ... 999 sDefault value10 sSelectioninf.Stop timeThe titration is stopped if the stop t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭718￭￭￭￭￭￭￭￭tiamo 2.1Titration directionSelection of the titration direction. If two endpoints are set, then the titr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭719TitrinoRange0.08 ... 16200 sDefault value2.00 s5.6.3.4.6.6 SET Upol - Stop conditionsTab: Method ▶

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭720￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0.01 ... 166.00 mL/minSelectionmaximumDefault valuemaximumTitrinoRange0.01 ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭721offNo drift correction takes place.Drift valueDrift value for drift correction. This parameter is on

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭722￭￭￭￭￭￭￭￭tiamo 2.1Only start titration by a start command from a SEND commandon | off (Default value: off)If this

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭723[New]Opens the dialog window Fix endpoint evaluation # to enter a new fixedendpoint (see Chapter 5.6

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭724￭￭￭￭￭￭￭￭tiamo 2.15.6.3.4.6.9 SET Upol - Additional measured valuesTab: Method ▶ SET Upol ▶ Properties... ▶ Addit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭725[Properties]Opens the dialog window External measured value # in which theparameters for the externa

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭60￭￭￭￭￭￭￭￭tiamo 2.12.4.4.5.3 Common logarithmDialog window: Formula editor ▶ Operators/FunctionsSyntaxy = Log

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭726￭￭￭￭￭￭￭￭tiamo 2.1Reagent addition takes place in three phases during the titration:￭ Initial dosingDuring this ph

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭727￭ KFT UpolAmperometric measurement with selectable polarization voltage (meas-ured value current I).

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭728￭￭￭￭￭￭￭￭tiamo 2.1￭ Additional measured valuesDefinition of additional measured values of other measuring commands

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭729Identification Description.EVTEnd volume (total dosed volume at the end of the com-mand) in mL.FIN C

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭730￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.MI.TEMTemperature with minimum measured value in °C.MI.TIMTime for th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭731Device typeDisplay or selection of the device type. If a device is selected under Devicename, then t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭732￭￭￭￭￭￭￭￭tiamo 2.1not definedNo tests will be carried out.SensorMeasuring inputSelection of the measuring input to

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭733continuousA temperature sensor must be connected. The temperature will then bemeasured continuously.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭734￭￭￭￭￭￭￭￭tiamo 2.15.6.3.5.2.3 KFT Ipol - Start conditionsTab: Method ▶ KFT Ipol ▶ Properties... ▶ Start condition

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭735Range0 ... 999999 sDefault value1 sPause 1Pause 1Waiting time, e.g. until the electrode has settled

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭612.4.4.5.5 Absolute valueDialog window: Formula editor ▶ Operators/FunctionsSyntax

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭736￭￭￭￭￭￭￭￭tiamo 2.1Range0 ... 999999 sDefault value0 s5.6.3.5.2.4 KFT Ipol - Control parametersTab: Method ▶ KFT I

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭737ControlNoteWill be displayed only if the User option is selected in the Titrationrate list box.Dynam

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭738￭￭￭￭￭￭￭￭tiamo 2.1Range0.1 ... 9.9 µL/minDefault valueminimum (slow), minimum (optimal), 5.0(fast) µL/minStop crit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭739Relative stop driftThe titration is stopped when the endpoint and the stop drift have beenreached. T

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭740￭￭￭￭￭￭￭￭tiamo 2.1Selection+ | - | autoDefault valueauto+positive measured value alteration-negative measured valu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭7415.6.3.5.2.6 KFT Ipol - Stop conditionsTab: Method ▶ KFT Ipol ▶ Properties... ▶ Stop conditionsComma

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭742￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange0.01 ... 150.00 mL/minSelectionmaximumDefault valuemaximum5.6.3.5.2.7 KFT Ipol - Co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭743Drift valueDrift value for drift correction. This parameter is only shown for Drift cor-rection = ma

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭744￭￭￭￭￭￭￭￭tiamo 2.1NoteConditioning must already be completed (= Condok) at the time theSEND command is received, o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭745[Delete]Deletes the selected line.Minimum evaluationMinimum evaluationon | off (Default value: off)I

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭62￭￭￭￭￭￭￭￭tiamo 2.12.4.4.5.7 IntegerDialog window: Formula editor ▶ Operators/FunctionsSyntaxy = Int(number)G

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭746￭￭￭￭￭￭￭￭tiamo 2.1Additional calculated measured valuesAdditional calculated measured valueson | off (Default valu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭7475.6.3.5.2.10 KFT Ipol - Fix endpoint evaluation Dialog window: Method ▶ KFT Ipol ▶ Properties... ▶

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭748￭￭￭￭￭￭￭￭tiamo 2.1ParametersThe parameters for the command KFT Upol are configured in the following8 tabs:￭ Genera

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭749Identification Description.DRICurrent and/or last drift for drift correction in µL/min.DSCTime for p

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭750￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.LP.EXxExternal value × (1...3) for the last measuring point ofthe mea

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭7515.6.3.5.3.2 KFT Upol - General/HardwareTab: Method ▶ KFT Upol ▶ Properties... ▶ General/HardwareCom

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭752￭￭￭￭￭￭￭￭tiamo 2.1855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectioninternal D0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭753U(pol)The polarization voltage is the voltage applied to the polarized electrodeduring an amperometr

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭754￭￭￭￭￭￭￭￭tiamo 2.1offNo stirrer will be used.Stirring rateSetting the stirring rate. The algebraic sign of the sti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭755Measured value driftThe measured value is only accepted if the drift is less than the value enteredh

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭632.4.4.5.9 SignDialog window: Formula editor ▶ Operators/FunctionsSyntaxy = Sign(n

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭756￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange0.00 ... 999.99 mLDefault value0.00 mLDosing rateSpeed at which the start volume is

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭757Titration rateTitration rateThe three predefined sets of parameters can be selected for the titratio

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭758￭￭￭￭￭￭￭￭tiamo 2.1Max. rateRate at which dosing is carried out outside of the Control range. The max-imum dosing r

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭759timeThe endpoint must be exceeded for a certain time: the Delay time. Thesame Delay time with differ

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭760￭￭￭￭￭￭￭￭tiamo 2.1Stop timeThe titration is stopped if the absolute stop time defined here has elapsedsince the st

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭761Titrando, 855Range-20.0 ... 150.0 °CDefault value25.0 °CTitrinoRange-170.0 ... 500.0 °CDefault value

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭762￭￭￭￭￭￭￭￭tiamo 2.1Stop timeTitrandoRange0 ... 999999 sSelectionoffDefault valueoffoffStops when the preset time (i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭763TitrandoRange1 ... 999 µg/minDefault value20 µg/minDrift correctionIf this parameter is set to autom

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭764￭￭￭￭￭￭￭￭tiamo 2.1Stabilizing timeWaiting period until the start of the titration during which the conditionrequir

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭765Fix endpoint evaluationFix endpoint evaluationon | off (Default value: off)If this check box is acti

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭64￭￭￭￭￭￭￭￭tiamo 2.1Type number, value range: 1 ... n. Direct entry as number or as formulaproviding a number.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭766￭￭￭￭￭￭￭￭tiamo 2.1Maximum evaluationMaximum evaluationon | off (Default value: off)If this option is enabled, then

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭767[Delete]Deletes the calculated measured value selected in the table.Additional external measured val

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭768￭￭￭￭￭￭￭￭tiamo 2.15.6.3.6 KFC5.6.3.6.1 KFC - OverviewDialog window: Method ▶ KFC ▶ Properties.. ▶ KFC - 'Co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭769￭ Additional evaluationsDefinition of additional methods for the evaluation of the titration curves.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭770￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.FP{x}.MEAMeasured value for the fixed endpoint × (1…9) in theunit of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭771Identification Description.NMPNumber of measuring points in the measuring point list.SMEStart measur

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭772￭￭￭￭￭￭￭￭tiamo 2.1SensorSensorSelection of a sensor of type Metal electrode from the sensors configuredin the sens

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭773offThe temperature will not be measured. The temperature entered man-ually under Temperature on the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭774￭￭￭￭￭￭￭￭tiamo 2.1851, 852Selection1 | 2 | 3 | 4 | offDefault value1offNo stirrer will be used.Stirring rateSettin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭775End pointEP atMeasured value for the endpoint.756, 831Range-2000.0 ... 2000.0 mVDefault value50.0 mV

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭65NoteUTC = Universal Time , from which the times in the various time zones ofthe ea

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭776￭￭￭￭￭￭￭￭tiamo 2.1DynamicsThe control range is entered as distance to the endpoint. Within the controlrange, iodin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭777Ipol 10 µA 20 µA 30 µAEP 50 mV 100 mV 150 mVDynamics 70 mV 100 mV 120 mVMax. rateMaximum rate with w

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭778￭￭￭￭￭￭￭￭tiamo 2.1Range1 ... 999 µg/minDefault value5 µg/minRelative stop driftThe titration is stopped when the e

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭779Time interval measuring pointTime interval for entering a measuring point in the measuring point lis

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭780￭￭￭￭￭￭￭￭tiamo 2.1Run subwindow displayed on the Single determination or Determina-tion series tab will then switc

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭781Range0 ... 99 sDefault value0 sAutomatic start after sample additionon | off (Default value: off)If

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭782￭￭￭￭￭￭￭￭tiamo 2.15.6.3.6.8 KFC - Additional evaluationsTab: Method ▶ KFC ▶ Properties... ▶ Additional evaluation

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭783Additional calculated measured valuesAdditional calculated measured valueson | off (Default value: o

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭784￭￭￭￭￭￭￭￭tiamo 2.15.6.3.6.10 KFC - Fix endpoint evaluation Dialog window: Method ▶ KFC ▶ Properties... ▶ Additio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭785ParametersThe parameters for the command BRC are configured in the following 8tabs:￭ General/Hardwar

Table of contents￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭VI￭￭￭￭￭￭￭￭tiamo 2.14.6.5 Information - Configuration ... 3334.6.6

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭66￭￭￭￭￭￭￭￭tiamo 2.1NoteUTC = Universal Time , from which the times in the various time zones ofthe earth are d

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭786￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.EMEEnd measured value (measured value after processingof the command)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭787Identification Description.LP.IGECurrent pulsed current for the last measuring point inthe measuring

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭788￭￭￭￭￭￭￭￭tiamo 2.1Device typeDisplay or selection of the device type. If a device is selected under Devicename, th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭789continuousA temperature sensor must be connected. The temperature will then bemeasured continuously.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭790￭￭￭￭￭￭￭￭tiamo 2.1Switch on/off automaticallyon | off (Default value: on)If this option is enabled, the stirrer wi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭791Max. waiting timeIf signal drift has been switched off or has not yet been reached, then themeasured

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭792￭￭￭￭￭￭￭￭tiamo 2.1optimalParameter set for all standard titrations; optimized for the most frequentapplications.fa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭793Range1.0 ... 999.0 µg/minDefault value15.0 (slow), 25.0 (optimal), 50.0 (fast) µg/minSelectionminimu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭794￭￭￭￭￭￭￭￭tiamo 2.1Extraction timeThe titration is not stopped until the extraction time has elapsed (even whenthe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭795Conditioningon | off (Default value: on)Enable/Disable the conditioning. If the conditioning is disa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭67NoteOnly the integral part is used for all parameters.A variable of the type Date/

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭796￭￭￭￭￭￭￭￭tiamo 2.1Stabilizing timeWaiting period until the start of the titration during which the conditionrequir

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭797Fix endpoint evaluationFix endpoint evaluationon | off (Default value: off)If this option is enabled

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭798￭￭￭￭￭￭￭￭tiamo 2.1[New]Opens the dialog window Calc. measured value # in which the parame-ters for the additional

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭799Fix valueValue of the fix endpoint.Measured valueRange-2000.0 ... 2000.0 mVTimeRange0.0 ... 999999.9

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭800￭￭￭￭￭￭￭￭tiamo 2.1CommandsDepending on the measured value, one of the following twoSTAT com-mands can be chosen:￭

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭8015.6.3.8.3 STAT - Evaluation windowDialog window: Method ▶ STAT ▶ Properties... ▶ Evaluations ▶ Rate

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭802￭￭￭￭￭￭￭￭tiamo 2.1Limit exceedingSelects the exceeded limit for which a track is to be started.SelectionLower limi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭803Cylin-der vol-umeMax. dosing rate Max. flow rate ExchangeunitDosingunitExchangeunitDosingunit1 mL 2

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭804￭￭￭￭￭￭￭￭tiamo 2.1￭ General/HardwareParameters for devices, dosing devices, sensors and stirrers.￭ Start condition

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭805Identification Description.FIN Command status; 1 = Command has ended at leastonce, 0, invalid (varia

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭68￭￭￭￭￭￭￭￭tiamo 2.1ExamplesNumberToText(-55.3) = -55.3NumberToText('CV.AverageTemp') = Vale of the c

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭806￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.MI.TEMTemperature with minimum measured value in °C.MI.TIMTime for th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭8075.6.3.8.6.2 STAT pH - General/HardwareTab: Method ▶ STAT pH ▶ Properties... ▶ General/HardwareComma

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭808￭￭￭￭￭￭￭￭tiamo 2.1855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectioninternal D0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭809SolutionInput of a solution name or selection of a solution from the solutions definedin the solutio

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭810￭￭￭￭￭￭￭￭tiamo 2.1SensorSelection of a sensor of type pH electrode from the list of sensors availablein the sensor

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭811Switch off automaticallyon | off (Default value: on)If this option is enabled, the stirrer will be s

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭812￭￭￭￭￭￭￭￭tiamo 2.1Min. waiting timeThe minimum waiting period is only important for drift-controlled measure-ments

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭813SelectionmaximumDefault valuemaximumTitrinoRange0.01 ... 150.00 mL/minSelectionmaximumDefault valuem

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭814￭￭￭￭￭￭￭￭tiamo 2.1Selection50 µL/min | 100 µL/min | 500 µL/min | UserDefault value100 µL/minControlNoteWill be dis

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭815Min. rateRate at which dosing is carried out at the very beginning of the titration andin the Contro

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭69TextToNumber('CV.DurchschnTemp') = Value of the variables (Avera-geTemp)

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭816￭￭￭￭￭￭￭￭tiamo 2.1-negative measured value alterationautoThe titration direction is determined automatically from

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭817SelectionoffDefault valueoffTitrinoRange-20.00 ... 20.00 SelectionoffDefault valueoffStart rateThe m

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭818￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange0.000 ... 9999.99 mLDefault value100.00 mLSelectionoffStop timeStops when the preset

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭819Filling rateSpeed with which the dosing cylinder is to be refilled after the titration. Themaximum f

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭820￭￭￭￭￭￭￭￭tiamo 2.1Lower hysteresis pHLower hysteresis of the measured value. If the measured value exceeds thelowe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭821Wait for [Continue]Reagent dosing in the current STAT command is interrupted and a mes-sage appears.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭822￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0.00 ... 166.00 mL/minDefault value166.00 mL/minTitrinoRange0.00 ... 150.00 mL

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭823NoteIf, when monitoring the dosing rate, the Lower limit is exceeded thenthe actions Wait for [Conti

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭824￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange-170.0 ... 500.0 °CDefault value500.0 °CUpper hysteresisUpper hysteresis of the temp

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭825[Properties]Opens the dialog window Track call # in which the parameters for thetrack call can be ed

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭70￭￭￭￭￭￭￭￭tiamo 2.1ExamplesTextToTime("2004-12-3 5:22:01 PM";"yMdhmsa") = 2004-12-0317:22:

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭826￭￭￭￭￭￭￭￭tiamo 2.1Moves the selected line down (changes the sequence).[New]Opens the dialog window Fix endpoint ev

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭8275.6.3.8.6.9 STAT pH - Additional measured valuesTab: Method ▶ STAT pH ▶ Properties... ▶ Additional

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭828￭￭￭￭￭￭￭￭tiamo 2.1[Properties]Opens the dialog window External measured value # in which theparameters for the ext

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭829ParametersThe parameters for the command STAT U are configured in the following8 tabs:￭ General/Hard

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭830￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.EMEEnd measured value (measured value after processingof the command)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭831Identification Description.MA.MEAMaximum measured value in the unit of the measuredvalue.MA.TEMTempe

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭832￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.SVAStart volume absolute (volume that was added accord-ing to the sta

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭833Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or exchange unit) wit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭834￭￭￭￭￭￭￭￭tiamo 2.1Dosing deviceSelection of the number of the dosing device (dosing or exchange unit) tobe used fo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭835TitrandoSelection1 | 2Default value1855Selection1Default value1TitrinoSelection1 | 2 | diff.Default

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭712.4.4.7.6 TimeToTextDialog window: Formula editor ▶ Operators/FunctionsSyntaxy =

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭836￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Selection1 | 2 | 3 | 4 | offoffNo stirrer will be used.Stirring rateSetting the sti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭837Measured value driftThe measured value is only accepted if the drift is less than the value enteredh

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭838￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange0.00 ... 999.99 mLDefault value0.00 mLDosing rateSpeed at which the start volume is

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭839TitrinoRange-2000 ... 2000 mVSelectionoffDefault valueoffTitration rateTitration rateThree predefine

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭840￭￭￭￭￭￭￭￭tiamo 2.1point for parameterization: Max. rate in mL/min = 0.005 • Expected rateof reaction in µL/min.Tit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭8415.6.3.8.7.5 STAT U - Titration parametersTab: Method ▶ STAT U ▶ Properties... ▶ Titration parameter

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭842￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0.1 ... 999999 sDefault value2.0 sTitrinoRange1 ... 999999 sDefault value2 sSt

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭8435.6.3.8.7.6 STAT U - Stop conditionsTab: Method ▶ STAT U ▶ Properties... ▶ Stop conditionsCommand n

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭844￭￭￭￭￭￭￭￭tiamo 2.1Last dosingThe stop time starts after the last increment has been dosed, i. e. the stoptime is r

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭845Monitoring Measured valueMonitoring Measured valueon | off (Default value: off)If this check box is

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭72￭￭￭￭￭￭￭￭tiamo 2.1Characters Significance ExampleEWeekday short formMon, Tue, WedEEEEWeekdayMonday, TuesdayDo

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭846￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855Range0.0 ... 2000.0 mVDefault value0.2 mVActionSelection of the event to be trigger

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭847TitrinoRange0.00 ... 150.00 mL/minDefault value0.00 mL/minLower hysteresisThe lower hysteresis repre

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭848￭￭￭￭￭￭￭￭tiamo 2.1Stop command (Titrando, 855)The running STAT command is quit, then the next command is executed.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭849Titrando, 855Range-20.0 ... 150.0 °CDefault value150.0 °CTitrinoRange-170.0 ... 500.0 °CDefault valu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭850￭￭￭￭￭￭￭￭tiamo 2.1Track call on limit exceedingIn this table, which cannot be edited directly, a maximum of 20 ent

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭851Fix endpoint evaluationFix endpoint evaluationon | off (Default value: off)If this option is enabled

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭852￭￭￭￭￭￭￭￭tiamo 2.1Range1.0 ... 2000.0 mV/mLDefault value25.0 mV/mL5.6.3.8.7.9 STAT U - Additional measured values

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭853[New]Opens the dialog window External measured value # in which theparameters for the external measu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭854￭￭￭￭￭￭￭￭tiamo 2.1If the activities of the acid and the conjugated base are equal (aA = aB), thenpH=pKa. This is t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭8555.6.3.9.2 Minimum/Maximum evaluationParameters: Method ▶ DET/MET/SET/KFT/KFC/MEAS ▶ Properties... ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭732.4.4.8 Text functions2.4.4.8.1 TextPositionDialog window: Formula editor ▶ Oper

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭856￭￭￭￭￭￭￭￭tiamo 2.15.6.3.9.4 Gran evaluationParameters: Method ▶ DET/MET ▶ Properties... ▶ Additional evaluations

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭8575.6.3.10 Additional measured values5.6.3.10.1 Calculated measured valueDialog window: Method ▶ DET

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭858￭￭￭￭￭￭￭￭tiamo 2.1Selectionempty | ppm | % | g/L | mg/L | mg/mL | mg/100g | mol/L | mmol/L | mL | g | mg | µg | °C

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭8595.6.4 Measuring commands5.6.4.1 Measuring commands - OverviewMenu item: Method ▶ Insert ▶ New comm

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭860￭￭￭￭￭￭￭￭tiamo 2.15.6.4.2 MEAS pH5.6.4.2.1 MEAS pH - OverviewDialog window: Method ▶ MEAS pH ▶ Properties.. ▶ ME

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭861Identification Description.BP{x}.TIMTime for the break point x (1…9) in s.BSY Command status; 1 = BU

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭862￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.MA.TEMTemperature for the maximum measured value in °C.MA.TIMTime in

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭863If the option not defined is selected as Device name, any device types ordevice groups which are abl

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭864￭￭￭￭￭￭￭￭tiamo 2.1offThe temperature will not be measured. The temperature manuallyentered under Temperature on th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭865Measurement with drift controlThe measurement is carried out drift-controlled if this option is enab

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭74￭￭￭￭￭￭￭￭tiamo 2.12.4.4.8.2 SubTextDialog window: Formula editor ▶ Operators/FunctionsSyntaxy = SubText(Text

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭866￭￭￭￭￭￭￭￭tiamo 2.1Max. waiting timeIf the signal drift has not yet been reached, then the measured value will beac

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭867Titrando, 855, 867Range0 ... 999999 sDefault value120 sTitrinoRange0 ... 9999 sDefault value120 sMea

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭868￭￭￭￭￭￭￭￭tiamo 2.15.6.4.2.4 MEAS pH - EvaluationsTab: Method ▶ MEAS pH ▶ Properties... ▶ EvaluationsCommand nameN

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭869Range0.1 ... 20.0 pH/sDefault value1.0 pH/sMaximum evaluationMaximum evaluationon | off (Default val

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭870￭￭￭￭￭￭￭￭tiamo 2.1WindowA range (window) can be defined on the measured value axis or on the timeaxis. The break p

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭871Additional calculated measured valuesAdditional calculated measured valueson | off (Default value: o

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭872￭￭￭￭￭￭￭￭tiamo 2.15.6.4.2.6 MEAS pH - Fix endpoint evaluation Dialog window: Method ▶ MEAS pH ▶ Properties... ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭873￭ General/HardwareParameters for devices, sensors and stirrers.￭ Measuring parametersParameters for

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭874￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.IMEInitial measured value (measured value before startconditions are

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭875The general parameters for the device, the sensor and the stirrer are definedon this tab.DeviceDevic

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭75ParametersTextThe parameter can be indicated either directly or as a variable of t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭876￭￭￭￭￭￭￭￭tiamo 2.1SelectionSensor name | pH electrode | Metal electrode |ISE electrodeDefault valueMetal electrode

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭8775.6.4.3.3 MEAS U - Measuring parametersTab: Method ▶ MEAS U ▶ Properties... ▶ Measuring parametersC

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭878￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855, 867Range0.1 ... 999.0 mV/minDefault value10.0 mV/minTitrinoRange0.5 ... 999.0 mV/

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭879Stop measured valueStops when the preset measured value has been reached since the start ofthe measu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭880￭￭￭￭￭￭￭￭tiamo 2.1offNo stop.TemperatureTemperatureMeasuring temperature which can be entered manually. If a tempe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭881[Properties]Opens the dialog window Fix endpoint evaluation # to edit the fixedendpoint selected in

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭882￭￭￭￭￭￭￭￭tiamo 2.1measured value can be evaluated as a break point for a small measured valuerange.Range0 ... 1.0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭883Window = TimeRange1 ... 999999 sDefault value999999 s5.6.4.3.5 MEAS U - Additional measured valuesT

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭884￭￭￭￭￭￭￭￭tiamo 2.1[New]Opens the dialog window External measured value # in which theparameters for the external m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭885Titrando: 808, 809, 835, 836, 841, 852, 857, 888, 890, 901, 904, 905,906, 907Titrino: 702, 716, 718,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1￭￭￭￭￭￭￭￭VII5.5 Tracks ...

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭76￭￭￭￭￭￭￭￭tiamo 2.1the type Text, Number or Date/Time. Entire operations can also be trans-ferred here.Value_f

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭886￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.ETEEnd temperature (temperature following processing ofthe command) i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭887Identification Description.STYType of stop with which the command was stopped:1 = normal;0 = manual

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭888￭￭￭￭￭￭￭￭tiamo 2.1851, 855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSelection of a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭889automaticIf a temperature sensor is connected then the temperature will be meas-ured continuously. O

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭890￭￭￭￭￭￭￭￭tiamo 2.1SelectionMeasurement with drift control | Measurementwithout drift controlDefault valueMeasureme

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭891Titrando, 855, 867Range0 ... 999999 sDefault value0 sMax. waiting timeIf the signal drift has not ye

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭892￭￭￭￭￭￭￭￭tiamo 2.1Measuring timeMaximum period of time for measurement.Titrando, 855, 867Range0 ... 999999 sDefaul

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭893TitrinoRange-170.0 ... 500 °CDefault value25.0 °C5.6.4.4.4 MEAS Ipol - EvaluationsTab: Method ▶ MEA

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭894￭￭￭￭￭￭￭￭tiamo 2.1Minimum evaluationMinimum evaluationon | off (Default value: off)If this option is enabled, then

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭895SlopeMinimum difference between the slope before and after the break point.The smaller the differenc

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭77ExamplesError('RS.IntermediateRes') = 0: the intermediate result was abl

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭896￭￭￭￭￭￭￭￭tiamo 2.15.6.4.4.5 MEAS Ipol - Additional measured valuesTab: Method ▶ MEAS Ipol ▶ Properties... ▶ Addit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭897[New]Opens the dialog window External measured value # in which theparameters for the external measu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭898￭￭￭￭￭￭￭￭tiamo 2.1Titrando: 808, 809, 835, 836, 841, 852, 857, 888, 890, 901, 904, 905,906, 907Titrino: 702, 716,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭899Identification Description.ETEEnd temperature (temperature following processing ofthe command) in °C

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭900￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.STYType of stop with which the command was stopped:1 = normal;0 = man

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭901851, 855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSelection of a sens

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭902￭￭￭￭￭￭￭￭tiamo 2.1automaticIf a temperature sensor is connected then the temperature will be meas-ured continuousl

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭903SelectionMeasurement with drift control | Measurementwithout drift controlDefault valueMeasurement w

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭904￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855, 867Range0 ... 999999 sDefault value0 sMax. waiting timeIf the signal drift has no

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭905Measuring timeMaximum period of time for measurement.Titrando, 855, 867Range0 ... 999999 sDefault va

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭78￭￭￭￭￭￭￭￭tiamo 2.1ASCII value(dec)Characters ASCII value(dec)Characters ASCII value(dec)Characters48 0 80 P 1

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭906￭￭￭￭￭￭￭￭tiamo 2.1TitrinoRange-170.0 ... 500 °CDefault value25.0 °C5.6.4.5.4 MEAS Upol - EvaluationsTab: Method ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭907Threshold valueThe evaluation of the minimum begins as soon as the slope of the curveexceeds the set

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭908￭￭￭￭￭￭￭￭tiamo 2.1SlopeMinimum difference between the slope before and after the break point.The smaller the diffe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭9095.6.4.5.5 MEAS Upol - Additional measured valuesTab: Method ▶ MEAS Upol ▶ Properties... ▶ Additiona

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭910￭￭￭￭￭￭￭￭tiamo 2.1[New]Opens the dialog window External measured value # in which theparameters for the external m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭911Robotic Titrosampler: 855Conductometer: 856AppearanceThe command has the following appearance:Parame

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭912￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.ETEEnd temperature (temperature following processing ofthe command) i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭913Identification Description.NMPNumber of measuring points in the measuring point list.STYType of stop

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭914￭￭￭￭￭￭￭￭tiamo 2.1851, 855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSelection of a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭9155.6.4.6.3 MEAS T - Measuring parametersTab: Method ▶ MEAS T ▶ Properties... ▶ Measuring parametersC

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭79ExamplesMolecular for-mulaMolar massH2SO498.0734Ca(OH)274.09268AlCl3*6H2O238.43174

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭916￭￭￭￭￭￭￭￭tiamo 2.1Titrando, 855, 867Range0.1 ... 999.0 °CDefault value0.5 °CTitrinoRange0.5 ... 999.0 °CDefault va

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭917Stop meas. valueStops when the preset measured value has been reached since the start ofthe measurem

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭918￭￭￭￭￭￭￭￭tiamo 2.1offNo stop.TemperatureTemperatureMeasuring temperature which can be entered manually. If a tempe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭919[Properties]Opens the dialog window Fix endpoint evaluation # to edit the fixedendpoint selected in

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭920￭￭￭￭￭￭￭￭tiamo 2.1EP criterionMeasure of the minimum sharpness of the break point. The smaller the EPcriterion set

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭921Window = Measured valueRange-20.0 ... 150.0 °CDefault value150.0 °CWindow = TimeRange1 ... 999999 sD

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭922￭￭￭￭￭￭￭￭tiamo 2.1Additional external measured valuesAdditional external measured valueson | off (Default value: o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭9235.6.4.7 MEAS T/Flow5.6.4.7.1 MEAS T/Flow - OverviewDialog window: Method ▶ MEAS T/Flow ▶ Propertie

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭924￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription.EGFLast measured gas flow rate (measured value followingprocessing of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭925Identifica-tionDescription.MI.TIMTime for the minimum measured value in s.MN.MEAAverage of the measu

2.5 Editing￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭80￭￭￭￭￭￭￭￭tiamo 2.1Copy selected text to the clipboard.Paste text from the clipboard.Open editor for entering a hyper

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭926￭￭￭￭￭￭￭￭tiamo 2.15.6.4.7.3 MEAS T/Flow - Measuring parametersTab: Method ▶ MEAS T/Flow ▶ Properties... ▶ Measuri

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭927Threshold valueThe evaluation of the minimum begins as soon as the slope of the curveexceeds the set

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭928￭￭￭￭￭￭￭￭tiamo 2.1[Properties]Opens the dialog window Calc. measured value # in which the parame-ters for the addi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭929ParametersThe parameters for the command MEAS Conc are configured on the fol-lowing 3 tabs:￭ General

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭930￭￭￭￭￭￭￭￭tiamo 2.1Identifica-tionDescription.LP.CAxCalculated value × (1...3) for the last measuring point ofthe m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭931Device typeDisplay or selection of the device type. If a device is selected under Devicename, then t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭932￭￭￭￭￭￭￭￭tiamo 2.1offThe temperature will not be measured. The temperature entered man-ually under Temperature on

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭933Measurement with drift controlThe measurement is carried out drift-controlled if this option is enab

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭934￭￭￭￭￭￭￭￭tiamo 2.1Range0 ... 999999 sDefault value52 sMeasuring intervalTime interval for entering a measuring poi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭935TemperatureTemperatureManually entered titration temperature. If a temperature sensor is connectedan

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1￭￭￭￭￭￭￭￭812.5.3 HyperlinkDialog window: HyperlinkThe dialog window Hyperlink serves for ent

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭936￭￭￭￭￭￭￭￭tiamo 2.1Additional external measured valuesAdditional external measured valueson | off (Default value: o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭937￭ Measuring parametersParameters for setting the measurement procedure.￭ EvaluationsDefining further

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭938￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.ITEInitial temperature (temperature before start conditionsare proces

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭939Identification Description.TC.C3Coefficient c3 of the Chebyshev polynomial of the sol-ution used.TC.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭940￭￭￭￭￭￭￭￭tiamo 2.1Temperature measurementType of temperature measurement856Selectioncontinuous | automatic | offDe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭9415.6.4.9.3 MEAS Cond - Measuring parametersTab: Method ▶ MEAS Cond ▶ Properties... ▶ Measuring param

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭942￭￭￭￭￭￭￭￭tiamo 2.1NoteA constant measured value is often only achieved after a certain time, asmixing and possibly

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭943856Range0.1 ... 999999.0 sDefault value2.0 sStop meas. valueStops when the preset measured value has

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭944￭￭￭￭￭￭￭￭tiamo 2.1offNo stop.TemperatureMeasurement temperatureTemperature of the solution to be measured. If a te

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭945Sample solutionSelection of the sample solution from the table Sample solutions (TCconductivity).Sel

3.1 Workplace - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭82￭￭￭￭￭￭￭￭tiamo 2.13 Workplace3.1 Workplace - General 3.1.1 Workplace - DefinitionProgram part: Workpl

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭946￭￭￭￭￭￭￭￭tiamo 2.1Minimum evaluationMinimum evaluationon | off (Default value: off)If this option is enabled, then

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭947SlopeMinimum difference between the slope before and after the break point.The smaller the differenc

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭948￭￭￭￭￭￭￭￭tiamo 2.15.6.4.9.5 MEAS Cond - Additional measured valuesTab: Method ▶ Commands ▶ MEAS Cond ▶ Properties

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭949[New]Opens the dialog window External measured value # in which theparameters for the external measu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭950￭￭￭￭￭￭￭￭tiamo 2.1ParametersThe parameters for the command MEAS TC Cond are configured on thefollowing two tabs:￭

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭951Identification Description.FP{x}.TIMTime in s until the fix endpoint × (1…9) is reached.IMEInitial m

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭952￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.TC.C3Coefficient c3 of the Chebyshev polynomial of the sol-ution used

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭953StirrerThis section is visible only if the 856 Conductivity Module was selected asdevice type.Stirre

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭954￭￭￭￭￭￭￭￭tiamo 2.1Range0 ... 999999 sDefault value3000 sMeasuring intervalTime interval for entering a measuring p

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭955Additional calculated measured valuesAdditional calculated measured valueson | off (Default value: o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭83￭ ToolsManual control, run test, sample tables, sample assignment tables, texttemplates.￭ HelpOpen

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭956￭￭￭￭￭￭￭￭tiamo 2.15.6.4.11 MEAS Ref5.6.4.11.1 MEAS Ref - OverviewDialog window: Method ▶ MEAS Ref ▶ Properties..

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭9575.6.4.11.2 MEAS Ref - General/HardwareTab: Method ▶ MEAS Ref ▶ Properties... ▶ General/HardwareComm

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭958￭￭￭￭￭￭￭￭tiamo 2.1End wavelengthUpper limit of the spectrum.Range200.0 ... 1100.0 nmDefault value1000.0 nmIntegrat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭959￭ General/HardwareParameters for device.￭ Measuring parametersParameters for setting the measurement

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭960￭￭￭￭￭￭￭￭tiamo 2.15.6.4.12.2 MEAS Spec - General/HardwareTab: Method ▶ MEAS Spec ▶ Properties... ▶ General/Hardwa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭961End wavelengthUpper limit of the spectrum.Range200.0 ... 1100.0 nmDefault value1000.0 nmIntegration

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭962￭￭￭￭￭￭￭￭tiamo 2.15.6.4.12.5 MEAS Spec - Evaluation window Dialog window: Method ▶ MEAS Spec ▶ Properties... ▶ Ev

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭963Command variablesThe following command variables are generated in the method run by thecommand MEAS

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭964￭￭￭￭￭￭￭￭tiamo 2.1Identification Description.LP.MEAMeasured value for the last measuring point in themeasuring poi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭965DeviceDevice nameSelection of a device from those available in the device table. The only devi-ces w

3.1 Workplace - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭84￭￭￭￭￭￭￭￭tiamo 2.1Properties RunwindowSets properties for the tab Single determination or Determination

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭966￭￭￭￭￭￭￭￭tiamo 2.1Range1 ... 10000 Default value10 SmoothingNumber of neighboring pixels with which the light inte

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭967Fix endpoint evaluationFix endpoint evaluationon | off (Default value: off)If this option is activat

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭968￭￭￭￭￭￭￭￭tiamo 2.1Threshold valueThe evaluation of the maximum begins as soon as the slope of the curveexceeds the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭969Time for the lower limit of the window.Window = Measured valueRange0 ... 4000 mAUDefault value0 mAUW

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭970￭￭￭￭￭￭￭￭tiamo 2.15.6.4.14 STDADD man5.6.4.14.1 STDADD man - OverviewDialog window: Method ▶ STDADD man ▶ Proper

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭971Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; invalid (variable

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭972￭￭￭￭￭￭￭￭tiamo 2.1DeviceDevice nameSelection of a device from those available in the device table. The only devi-c

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭973Selectioncontinuous | automatic | offDefault valueautomaticcontinuousA temperature sensor must be co

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭974￭￭￭￭￭￭￭￭tiamo 2.1Number of additionsNumber of times the standard solution is to be added.Range1 ... 19 Default va

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭975DeviceConcentration unit of addition solution.Selectionmol/L | mmol/L | µmol/L | ppm | g/L | mg/L |µ

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1￭￭￭￭￭￭￭￭85Change layoutChanges layout of the loaded workplace view (see Chapter 3.1.7.2, page 88).Load viewL

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭976￭￭￭￭￭￭￭￭tiamo 2.1Measuring intervalTime interval for entering a measuring point in the measuring point list.Range

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭977pH/Ion - Meter: 867Robotic Titrosampler: 855AppearanceThe command has the following appearance:Param

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭978￭￭￭￭￭￭￭￭tiamo 2.1Identifi-cationDescription.ENPElectrode zero point calculated from the calibration.ETEEnd temper

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭979not definedIn this case, the device name must be assigned by the user at the start ofthe method.Devi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭980￭￭￭￭￭￭￭￭tiamo 2.1NoteIf an existing solution is selected as the solution to be added then theConcentration and Un

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭981StirrerStirrerSelection of the stirrer.Selection1 | 2 | 3 | 4 | offDefault value1offMeans that no st

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭982￭￭￭￭￭￭￭￭tiamo 2.1Addition modeSelectionFixed volume increments | Variable volumeincrementsDefault valueFixed volu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭983Dosing rateSpeed at which the volume increments are added. The maximum dosingrate depends on the cyl

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭984￭￭￭￭￭￭￭￭tiamo 2.1Measuring intervalTime interval for entering a measuring point in the measuring point list.Range

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1￭￭￭￭￭￭￭￭985Titrando: 808, 809, 835, 836, 857, 904, 905, 906, 907pH/Ion - Meter: 867Robotic Titrosampler: 855App